The internal loadings at a cross section through the 150-mm-diameterdrive shaft of a turbine consist of an axial force of 12.5 kN, a bendingmoment of 1.2 kNm, and a torsional moment of 2.25 kN. m. (Figure 1).Figure1.2 kN-m12.5 kN2.25 kN-m1 of 1Part ADetermine the principal stresses at point B.Express your answers using three significant figures separated by a comma.01,02 =IVE ΑΣΦvecSubmit Previous Answers Request Answer?MPa

Given Data The diameter of the shaft d= 150 mm The Axial force F=-12.5KN=-12500N The Bending Moment…

Answered: Determine the principal stresses at…

Engineering

Mechanical Engineering

Determine the principal stresses at point B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The block is subjected to axial loa normal tension developed at poir the distribution of the normal…

Q: бх Oy Txy στ Txy бу In the diagram above, σ = 100 MPa, σy = -27 MPa,, and Tzy = 40 MPa. Let each…

Q: Determine the stress components acting on the inclined plane AB. Solve the problem using the method…

A: Data given-

Q: The steel pipe AB has a 72mm outer diameter and a 5mm wall thickness. Knowing that the arm CDE is…

Q: The internal loadings act on the section. Show the stresses with their directions that each of these…

Q: Problem 6. The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits…

A: Given: The outer radius of pipe ro=20 mm=0.02 m The inner radius of pipe ri=15 mm=0.015 m Distance…

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: If the principal stresses are of opposite signs, then failure occurs in the plane. True or false?

A: Given: The maximum principal stress is σ1=σ. The minimum principal stress is σ2=- σ.

Q: Determine the stress components acting on the plane AB. Solve the problem using the method of…

Q: For the stress shown below, determine the cross-sectional areas of bars BE, BF and CF so that the…

A: For the stress shown below,Determine the cross-sectional areas of bars BE, BF and CF so that the…

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

Q: A thin hollow sphere of radius 300 mm and thickness 2.5 m is subjected to an internal pressure.…

A: Thin spherical shell is given Tensile stress in sphere = σ = 360 kPa Radius of sphere = r = 300 mm…

Q: The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and shear…

Q: F14-8. Use Mohr's circle to determine the principal stresses at the poinLAlso, find the…

A: Given: The stress acting on element in x-direction, σx= 80 kPa The shear stress acting on element,…

Q: 13/ 12 a 1 m 2 m a

Q: The tubular shaft of the soil auger is subjected to the axial force and torque shown. If the auger…

A: Given data:Axial force P=1,200 lbTorque T=3000 lb.ftDetermine : The state of stress at point A and B…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

The internal loadings at a cross section through the 150-mm-diameter
drive shaft of a turbine consist of an axial force of 12.5 kN, a bending
moment of 1.2 kNm, and a torsional moment of 2.25 kN. m. (
Figure 1).
Figure
1.2 kN-m
12.5 kN
2.25 kN-m
1 of 1
Part A
Determine the principal stresses at point B.
Express your answers using three significant figures separated by a comma.
01,02 =
IVE ΑΣΦ
vec
Submit Previous Answers Request Answer
?
MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data and Find out

VIEW

Step 2: The Sectional Properties of the object

VIEW

Step 3: Axial stress and Torsional Stress

VIEW

Step 4: The Principal stress at point B

VIEW

Solution

VIEW

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the normal stress developed at points A and B. Neglect the weight of the block.
Initially, gaps between the A-36 steel plate and the rigid constraint are as shown. Determine the normal stresses sx and sy in the plate if the temperature is increased by T = 100F. Hint: To solve, add the thermal strain aT to the equations for Hooke’s law
5. Two forces act on the solid circular rod (r=.005 m) as shown. Using Mohr's circle, determine the principal stresses and the absolute maximum in plane shear stress at point A. 100 mm 150 mm 500 N V 300 N -•64- o (M Pa) 6.l12 -64 T (MPa) Taug = 6.l12 R=Vo2037+ 3.0562 =3.062 M Pa O; = R+ Jarg; 0,=60119MPQ t 3.0 0056 M Pa T,= Oava - R; 2 0068 MPaa Therefore Tabs =R= 3.062MPaa max
The solid cylinder having a radius r is placed in a sealed container and subjected to a pressure p. Determine the stress components acting at point A located on the center line of the cylinder. Draw Mohr's circles for the element at this point. A
Question 2. The hollow steel shaft has a diameter of 65 mm and thickness of 5mm, is subjected to a torque and moment produced by a 3 kN force which is 15 mm from the centre of the shafts cross section. The shafts have the same centroid. a. Using Mohr's circle, determine the principal stress, maximum in-plane shear stress and average normal stress in the at point J and K. b. If the weld has a 30° at point J, what is the maximum shear stress the weld has to with- stand. K 700 mm F=3kN 15 mm c. Determine the maximum bending stress if the hole in the cross section area is now off centre by 2 mm in the x and y direction.
The W-kg man stands in the position shown. If the center of gravity of the man is at Gand assuming that the contact point at C is smooth.a) Find the reactions at B and C. b) Determine the state of stress at point A on the cross section of the plank at sectiona–a (Cubic stress element in 2D).
The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy= 300 lbf and Fx= Fz= 0 lbf. The length of the rod DC denoted by L1 is given to be 11 in. The length of the rod AB denoted by L2 is given to be 10 in. !! %3D NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 2 in L2 in 1-in dia t-in R. |2 in l-in dia. I-in dia. -in dia. Li in B.
Two wood members of uniform cross section are joined using a simple glued scarf splice. Determine the normal and shearing stresses in the glued splice. The column is loaded in tension through the centroid with the load indicated. 2.4 kip 6" 60° 2.4 kip
Thank you in advance, note it ask for stress a B
Determine the shortest distance d to the edge of the plate at which the force P can be applied so that it produces no compressive stresses in the plate at section a–a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness.
Similar problem already solved on bartleby. Take reference from there.
The bent shaft is fixed in the wall at A. If a force F is applied at B (the force is acting on the plane parallel to the x-o-y plane). Take F = 54 N and 0 = 45°. 1. Determine the internal forces acting on the section containing points D and E 2. Determine the normal stress component acting at point E 3. Determine the shear stress component developed at point E 4. Draw the state of stress on a volume element (stress element) located at point E 5. Determine the principal stresses acting at point E by constructing Mohr's circle A 150 mm E 200 mm 30 mm 75 mm B F