Determine the percentage increase in power capacity made possible in changing over from flat belt drive to V-belt drive. The diam

Q: Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0…

A: GivenI=80 lb-ft2N1=0  to N2=1500rpm in t=3sTstart=10 in lb=1012 lb ft=1012×32.17 lb ft=26.808 lb…

Q: (12) What is the value of F? (A) 7.53 N; (B) 8.03 N; (C) 8.53 N; (D) 9.03 N; (E) 9.53 N.

A: 12. According to the given data, Pressure is similar for both cylinders. Therefore,

Q: Flat Belts. Two shafts 10 ft apart, with axes in the same horizontal plane, are to be connected with…

A: Two shafts 10 ft apart Power H = 25 hp n = 900 rev/min

Q: and 45 mm respectively. The coefficie m for thread and collar are 0.15 and 0. rely: The machinist…

A:

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm.The…

A:

Q: The ratio of tension on the tight side to that of the slack ride in a flat belt drive is

A: Given, find the ratio of tension on the tight side to that of the slack ride in a flat belt drive

Q: Determine the given question with correct solution

A: Given data; P=25 KW=25×103 WN=300rpmp=85 KN/m2=0.85 N/m2d2=380 mmr2=190 mmn=2μ=0.25 Find,1.outer…

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: Solve the problem, show your complete solution. Answer must be in 3 decimal places. 1. A…

A:

Q: There is 465 psi in the hydraulic system that is powering a caliper with two pistons on each side of…

A: The normal force exerted by the caliper on the rotor can be determined as,

Q: 1- Does increasing the contact angle between the belt and pulley affect the amount of friction…

A: Belt and Pulley system is used to transmit power from one shaft to another shaft. In this mechanism…

Q: is necessary to start the system of blocks moving to the right? The coefficient of friction is 0.10…

A:

Q: A single plate friction clutch with both sides of plate being effective is used to transmit power at…

A: Given:Outer radius, r2=10 cm or 100 mminner radius, r1=8 cm or 80 mmEngine speed, N=2000 rpmMaximum…

Q: l-plate clutch must transmit 23 kW of power without slipping at 2500 rev/min. The coefficient of…

A:

Q: A disc clutch is required yo transmit 5 kW at 2000 rpm with coefficient of friction 0.25 and bore…

A: Given                      Power, P = 5 kW Coefficient of friction = 0.25  Constant pressure, P = 1…

Q: =ust is carried on a collar of 100 mr er and 60 mm inner diameter. The ficient of friction at the…

A:

Q: Give the suitable dimensions of a leather open flat-belt system according to the standards having…

A: Belt drives are used to transfer power from one shaft to another using pulleys that rotate at the…

Q: A multiple disk clutch consisting of 3 disks on the driving shaft and 2 disks on the driven shaft is…

A:

Q: Determine the resulting torque of a uniform pressure frictional clutch having 4 discs in the driving…

A:

Q: The semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque required to…

A: Cone clutch is mainly used in automobiles. Cone clutch has only one pair of friction surface. In…

Q: Static friction keeps you in your seat.

A: In the given statement it mentions that static friction helps us to sit on the sit properly

Q: The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.4;…

A:

Q: A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter…

A: GIVEN DATA-  m=585kg  dm=20mm p=5mm Coefficient of friction =0.1 We have to find torque required to…

Q: Calculate the retraction force output for a double acting linear actuator with a piston diameter of…

A:

Q: per surface is 66 Nm. Calculate the required number of discs n.

A: Total torque = torque per surface × (No. of plate…

Q: 2a-e. Outline five transmission problems its causes and their solutions.

A: A transmission is a mechanism that offers regulated power application in a power transmission…

Q: Derivation of the relationship between tensile strength, contact angle and friction coefficient of a…

A:

Q: An automobile single plate clutch consists of a pair of contacting surfaces. The inner and outer…

A: Uniform pressure theory: When the clutch and bearing mating components are fresh, the contact…

Q: The tension, Tiial of V-belt with groove of 60° during initial adjustment is 150 N on each side. The…

A: Given Data: Tinitial =150NGroove angle α = 60°Angle of lap θ = 165°Coefficiet of friction μ =…

Q: In detail describe and discuss gearless traction elevators

A: Gearless Traction elevators: The gearless traction elevators are described by the given parameters,…

Q: (i) The diameters of pulleys; (ii) The length of the belt and (iii) Belt tensions on the tight and…

A:

Q: For a radial bearing the desired rated life is 10000 hours for a speed of 600 rpm and radial load of…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.