Determine the heat loss by radiation from an oven wall to the wall of a room to which the oven wall is directly facing. Assume that no heat flows through the adjacent walls, which are coated with a reradiating material. The oven wall is square, 4 ft on one side, and is 2 ft from the room wall and parallel to it. The oven wall is steel sheet and is at 400°F, and the wall is at 80°F and is of asbestos board.

Determine the heat loss by radiation from an oven wall to the wall of a room to which the oven wall is directly facing. Assume that no heat flows through the adjacent walls, which are coated with a reradiating material. The oven wall is square, 4 ft on one side, and is 2 ft from the room wall and parallel to it. The oven wall is steel sheet and is at 400°F, and the wall is at 80°F and is of asbestos board.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter11: Heat Transfer By Radiation

Section: Chapter Questions

Problem 11.41P: 11.41 Determine the steady-state temperatures of two radiation shields placed in the evacuated space...

See similar textbooks

Similar questions

1.11 Calculate the heat loss through a glass window 7-mm thick if the inner surface temperature is 20°C and the outer surface temperature is 17°C. Comment on the possible effect of radiation on your answer.
A long wire 0.7 mm in diameter with an emissivity of 0.9 is placed in a large quiescent air space at 270 K. If the wire is at 800 K, calculate the net rate of heat loss. Discuss your assumptions.
Determine the power requirement of a soldering iron in which the tip is maintained at 400C. The tip is a cylinder 3 mm in diameter and 10 mm long. The surrounding air temperature is 20C, and the average convection heat transfer coefficient over the tip is 20W/m2K. The tip is highly polished initially, giving it a very low emittance.
8.15 A mercury bath at is to be heated by immersing cylindrical electric heating rods, each 20 cm tall and 2 cm in diameter. Calculate the maximum electric power rating of a typical rod if its maximum surface temperature is .
1.47 A flat roof is modeled as a flat plate insulated on the bottom and placed in the sunlight. If the radiant heat that the roof receives from the sun is , the convection heat transfer coefficient between the roof and the air is 12 W/m2 K, and the air temperature is , determine the roof temperature for the following two cases: (a) Radiative heat loss to space is negligible, (b) The roof is black and radiates to space, which is assumed to be a black- body at 0 K.
11.41 Determine the steady-state temperatures of two radiation shields placed in the evacuated space between two infinite planes at temperatures of 555 K and 278 K. The emissivity of all surfaces is 0.8.
1.28 The sun has a radius of and approximates a blackbody with a surface temperature of about 5800 K. Calculate the total rate of radiation from the sun and the emitted radiation flux per square meter of surface area.
Determine the heat flow between the roof and floor of 4 x 3 m size of a furnace of 4 m x 4 m x 3 m size when the roof is at 1200 K and the floor is maintained at 600 K, with the other surfaces non absorbing and reradiating. The surface emissivity of the hotter surface is 0.8 and that of the cooler surface 0.6.
Determine the heat flow between the roof and floor of 4 × 3 m size of a furnace of 4 m × 4 m × 3m size when the roof is at 1200 K and the floor is maintained at 600 K, with the other surfaces non-absorbing and reradiating. The surface emissivity of the hotter surface is 0.8 and that of the cooler surface 0.6.
Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled on the lower section. The wafer is placed such that the top and bottom surfaces of the wafer exchange radiation with the hot and cold zones respectively of the furnace. The zone temperatures are Tsur = 1100 K and Turc = 330 K. The emissivity and thickness of the wafer are = 0.65 and d = 0.78 mm, respectively. With the ambient gas at T = 700 K, convection heat transfer coefficients at the upper and lower surfaces of the wafer are 8 and 4 W/m².K. Find the steady-state temperature of the wafer, in K. sur, Tw = i K
The glass surfaces are polished, having an emissivity of 0.095. The diameters of the inner and outer cylinders are 9 cm and 11 cm respectively and their length is 20 cm. The temperature of the inner and outer cylinders is 92oC and 31oC respectively. Calculate the heat transfer coefficient due to radiation through the cylindrical surface from the inner to the outer cylinder.
A flat-plate solar collector, as shown in Fig. 1, is used to heat water by having water flow through tubes attached at the back of the thin solar absorber plate. The absorber plate has an emissivity and an absorptivity of 0.8. The top surface (* = 0) temperature of the absorber is To = 35 °C, and solar radiat ion is incident on the absorber at 600 W/m? with a surrounding temperature of 0 °C. The convection heat transfer coefficient at the absorber surface as 8 W/m?-K. Assuming constant thermal conductivity and no heat generation in the wall, i express the differential equation and the boundary conditions for steady one- dimensional heat conduct ion through the wall, obtain a relation for the variation of temperature in the wall by solving the differential equation, and ii iii. determine the net heat flux, ġo absorbed by the collector ε, α, Τ. Absorber plate Water tubes Insulation Fig. 1