An enclosure has an inside area of 50 m², and its inside surface is black and is maintained at a constant temperature. A small opening in the enclosure has an area of 0.03 m². The radiant power emitted from this opening is 52 W. What is the temperature of the interior enclosure wall, in K? If the interior surface is maintained at this temperature, but is now polished so that its emissivity is 0.15, what will be the value of the radiant power emitted from the opening, in W? T₁ = grad = i K W

An enclosure has an inside area of 50 m², and its inside surface is black and is maintained at a constant temperature. A small opening in the enclosure has an area of 0.03 m². The radiant power emitted from this opening is 52 W. What is the temperature of the interior enclosure wall, in K? If the interior surface is maintained at this temperature, but is now polished so that its emissivity is 0.15, what will be the value of the radiant power emitted from the opening, in W? T₁ = grad = i K W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the net heat flux per unit area and by radiation between two infinitely large parallel plates with a very small space between them. They both behave as black bodies and are kept at 1000K and 500K, respectively.
Earth absorbs solar energy and radiates infrared energy. The intensity of the solar radiation incident on earth is J = 1350 Wm-2, also known as the solar constant. Assume earth’s surface (ground) temperature to be uniform at Ts, and that the ground and atmosphere are black (emissivity = 1) for infrared radiation. The radius of the earth is 6.378 x 106 m. The diagram shows the ground at the surface temperature Ts and the atmosphere, represented as a thin black layer, at temperature Ta . Suppose the atmosphere absorbs 100% of the infrared radiation emitted by the ground. Assume that the ground absorbs 47.5% of the incident solar energy, and that the atmosphere absorbs 17.5% of the incident solar energy (for a total of 65% absorbed by the planet). Calculate the "steady state” numerical values of the earth’s ground temperature Ts and the atmospheric temperature Ta taking into account the “greenhouse effect” of atmospheric infrared absorption and emission described above.
- A furnace can be considered like a long semicylindrical duct of diameter D = 5 m. The base (1) and the dome (2) of the furnace have emissivity's of 0.5 and 0.9 and are maintained at uniform temperatures of 305 and 1000 K, respectively. a- Draw the network of the system. b- Calculate total resistance. b- Determine the net rate of radiation heat transfer per unit length from the dome to the base surface.
A furnace is located next to a dense array of cryogenic fluid piping. The ice-covered piping approximates a plane surface with an average temperature of Tp = 0°C and a total, hemispherical emissivity of εp = 0.56. That is, the piping can be replaced by a flat surface with the given properties. The furnace wall has a temperature of Tf = 247°C and a total, hemispherical emissivity of εf = 0.86. To minimize the heat loading on the regirgeration equipment and piping, a reflective aluminum radiation shield with a total, hemispherical emissivity of εs = 0.13 on each of its sides is installed between the pipiing and the furnace wall as shown. Assume that all surfaces are diffuse and gray and treat the problem as one-dimensional (surfaces form infinite parallel plates). What is the heat load on on the refrigeration unit? That is, what is the net radiative power at the surface which approximates the dense array of ice-cold piping, qrad,p in Watts?
A 30 x 30 cm door in a brick kiln is at a distance of 3.5 m from a wall 12 m wide and 5 m high. The door is so located that a normal from the center of the door strikes the wall midway from the ends and 1.5 m above the floor. The opening into the kiln may be considered a black body; the wall is painted flat paint (Ɛ = 0.46). The temperature inside the kiln is 1 400 C and the wall temperature is 60 C. Determine (a) the configuration factor F12 and (b) the net radiant heat exchange between the opening and the wall when the fire door is open?
A furnace is located next to a dense array of cryogenic fluid piping. The ice-covered piping approximates a plane surface with an average temperature of Tp = 0°C and a total, hemispherical emissivity of εp = 0.53. That is, the piping can be replaced by a flat surface with the given properties. The furnace wall has a temperature of Tf = 206°C and a total, hemispherical emissivity of εf = 0.83. To minimize the heat loading on the regirgeration equipment and piping, a reflective aluminum radiation shield with a total, hemispherical emissivity of εs = 0.14 on each of its sides is installed between the pipiing and the furnace wall as shown. Assume that all surfaces are diffuse and gray and treat the problem as one-dimensional (surfaces form infinite parallel plates). What is the heat load on on the refrigeration unit? That is, what is the net radiative power at the surface which approximates the dense array of ice-cold piping, qrad,p in Watts?
Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled on the lower section. The wafer is placed such that the top and bottom surfaces of the wafer exchange radiation with the hot and cold zones respectively of the furnace. The zone temperatures are Tsur,h = 1050 K and Tsur.e = 330 K. The emissivity and thickness of the wafer are e = 0.65 and d = 0.78 mm, respectively. With the ambient gas at T. = 700 K, convection heat transfer coefficients at the upper and lower surfaces of the wafer are 8 and 4 W/m²-K. Find the steady-state temperature of the wafer, in K. Tw i K
A composite wall is comprised of two large plates separated by sheets of refractory insulation. In the installation process, the sheets of thickness L = 50 mm and thermal conductivity k = 0.05 W/mK are separated at 1-m intervals by gaps of width w = 10 mm. The hot and cold plates have temperatures and emissivities of T1 = 400 deg C, emissivity1 = 0.85 and T2 = 35 deg C, emissivity2 = 0.5, respectively. Assume that the plates and insulation are diffuse-gray surfaces. %3D Determine the heat loss by radiation through the gap per unit length of the composite wall (normal to the page). Recognizing that the gaps are located on a 1-m spacing, determine what fraction of the total heat loss through the composite wall is due to transfer by radiation through the insulation gap. Hot side Gap w = 10 mm A. 47 W/m, 9.2% T1 = 400°C B. 47 W/m, 10.2% L = 50 mm C. 37 W/m, 10.2% D. 37 W/m, 9.2% T2 = 35°C Cold side 1 m Insulation, k = 0.05 W/m-K
This experiment is conducted to determine the emissivity of a certain material. A long cylindrical rod of diameter D₁ = 0.01 m is coated with this new material and is placed in an evacuated long cylindrical enclosure of diameter D₂ = 0.1 m and emissivity 2 = 0.95, which is cooled externally and maintained at a temperature of 200 K at all times. The rod is heated by passing the electric current through it. When steady operating conditions are reached, it is observed that the rod is dissipating electric power at a rate of 16 W per unit of its length, and its surface temperature is 600 K. Based on these measurements, determine the emissivity of the coating on the rod. The emissivity of the coating on the rod is 0.1165
A long electrical conductor of 10 mm diameter is concentric with a refrigerated cylindrical tube of 50 mm diameter whose surface has an emissivity of 0.9 and temperature of 27 °C. The electrical conductor has a surface emissivity of 0.6 and dissipates 6.0 W per meter length. Assuming that the space between the two surfaces is empty, calculate the surface temperature of the conductor.
Consider a cuboidal furnace (l = 5 m, b = 4 m, h = 3 m), whose surfaces closely approximateblack surfaces. The base, top, and side surfaces of the furnace are maintained at uniformtemperatures of (1040) K, (840) K, and (540) K, respectively. Determine (a)the net rate of radiation heat transfer between the base and the side surfaces, (b) the net rate ofradiation heat transfer between the base and the top surface, and (c) the net radiation heattransfer from the base surface. Steam in a heating system flows through tubes whose outer radius is r1 = (3) cm and whosewalls are maintained at a temperature of 127 °C. Circular aluminum fins (k = 180 W/m K) ofouter radius r2 = (6) cm and constant thickness t = 1 mm are attached to the tube. The spacebetween the fins is 3 mm. Heat is transferred to the surrounding air at 27 °C, with a combinedheat transfer coefficient of 60 W/m2 K. Determine the increase in heat transfer from the tubeper meter of its length as a result of adding fins
Two very large parallel plates are kept at uniform temperatures T1=800 K and T2=500 K, and have emissivities ε1=0.2 y ε2=0.7, respectively, as shown in the figure. Determine the net rate of radiation heat transfer between the two surfaces per unit surface area of the plates.