Determine the degree of indeterminacy of the structure.

Q: a. Horizontal component (indicate the direction) of the total hydrostatic force acting on the gate.…

A: Horizontal component (F) of the pressure force is equal to the projection of the curved surface on…

Q: Determine: The location of plastic neutral axis form the top edge of the flange in mm.

A:

Q: Question 1. Determine the degree of indeterminacy of the below structures: (a) (b) pin (d)

A:

Q: advantage and disadvantage of frame structure

A:

Q: Determine major principal and minor principal stress

A: Given data : Normal stress along X axis (σ1)=866 N/cm2Normal stress along Y axis (σ2)=600 N/cm2Shear…

Q: pressure gauges to show the same r

A: Diameter of large section is d1= 300mm or .3m Discharge at gauges = .4m3/sec Datum head of smaller…

Q: What force is required to punch a 20-mm diameter hole through a 10-mm thick plate? The ultimate…

A:

Q: For the structure shown, 1. Determine the degree of indeterminacy 2. Determine equivalent statically…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: Classify the structure below as determinate or indeterminate and what degree of indeterminacy.

A: Criteria as such  1. If R - 3 = 0 then It is Determinate  2. If R - 3 > 0 then it is…

Q: Find each Reaction. Show a correct FBD.

A:

Q: An electrical resistance strain rosette indicates strains of -400, +800 and +500 along the x, y and…

A: Given- strains values--400, +800, +500angle=45o

Q: Determine the location (x̄, y̅, z̅) of the centroid of the homogeneous rod.

A: Consider the free body diagram of the homogeneous rod shown below. The length of each segment with…

Q: 3.6 1.0 1.0 \33.179° 33.179°/ 0.2 1.0 1.0 33.179° 33.179° .8 1.0 1.0 \33.179° 33.179° .4 52.595°…

A: for analysing the structure use equation of equilibrium we use joint method for analysing the…

Q: 3–3. Classify each of the following tr determinate, indeterminate, or unstable state its degree.

A:

Q: Details of columbs law of shear strength

A: Coulomb 's law of shear strength is used to evaluate  the total shear strength of a soil having…

Q: en the two layers of the bars.

A: Given Data:Square footing size = 4.31m×4.31mColumn size = 331×361mmDead load = 586kNLive load =…

Q: Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional area…

A:

Q: Q#4: A) Illustrate the bond beam in your own words. Also write few lines about the diaphragm and…

A: A bond beam is a horizontal structural component, typically found as an embedded a part of a masonry…

Q: degree of indeterminacy and stability

A: Given: The frame structures with storey To find: The indeterminacy and stability

Q: Determine the degree of indeterminacy (i) of the structure shown below: Hinge Hinge

A: As per our guidelines we are supposed to answer first question only if not mentioned to answer any…

Q: Determine static , external and internal determinacy

A: Given data : Number of external support reaction (R)=2+1=3Number of member (m)=12Number of joint…

Q: Hiwe A bar with constant ss-section area(Aland unit weight () is subjected to axial force ce) in…

A:

Q: Calculate vertical components at point C

A:

Q: Two forces are applied to the construction bracket as shown. Determine the angle e which makes the…

A: The free-body diagram is shown below,

Q: 11 Which of the following statements is correct about the given structure? It is a determinate…

A:

Q: force equal to -100 kN

A:

Q: 600 mm diameter column contains 20-28 mm diameter longitudinal bars

A: Given: D = 600 mm Clear cover = 40 mm Assume fck = 25 MPa Diameter of Spiral bar = 10 mm To…

Q: What is the magnitude of the force on the structural member AB in kips?

A:

Q: The degrees of indeterminacy of the given structure is pin 3 O 4 O 5

A:

Q: Internal Hinge 白 0 目

A:

Q: What is the depth of the compression block in mm

A: depth of compression block: 0.85f'cab = Asfy A = 3060 mm2 0.85 x 35 x a x 1200 = 3060 x 420  a = 36…

Q: For the given structures, determine the degree of indeterminacy. 7. A

A:

Q: EXAMPLE : BEAM Check statical determinacy of the structure a) b) Hinge c) d)

A:

Q: For the given structures, determine the degree of indeterminacy. 8.

A: External indeterminacy = re - 3 = 6 -3 = 3 Internal indeterminacy = 3C - rr…

Q: Define Statically Indeterminate Structures.

A:

Q: Which of the following best describe the structure? statically indeterminate to Istdegree statically…

A:

Q: Which of the following statements is correct about the given structure? O A C E C pin fixed roller…

A:

Q: What is the degree of indeterminacy of the given structure? a. -1 b. 0 .1 d. 2

A: The introduction of an internal hinge in a rigid frame provides an additional equation of…

Q: 5 kN 4 kN 3 kN 2 kN -3 m 3 m 3 m - A C E 4 m

A:

Q: e f A roller B Foller roller

A:

Q: 4cm r=2om 12cm r=2cm 4cm 3cm 6cm 3cm '(c)

A:

Q: The dimension of the base of pyramid is 4 m x 6 m

A: Given: A frustum of rectangular pyramid immersed in water. The base dimension of pyramid is 4 m x 6…

Q: Four cables are used to lift a precast concrete slab with dimensions 3 m x 3 m and 76 mm thick. The…

A:

Q: Determine the cohesion

A: Given data : Shearing stress (S)=250 KPaNormal stress (σ)=480 KPaAngle of internal friction…

Q: Determine the force in the following: AB AE BC BE EC ED CD State whether the members are in…

A: We can find the forces in the given truss using the Method of joints. Members having forces moving…