What is the depth of the compression block in mm

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P…

A:

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A:

Q: Bar ABC has an outer diameter of 10 mm and is made of red brass for which E = 100 GPa. Section AB is…

A: Consider the BC portion of the beam:

Q: 150 12 mm N.A 466.09 mm

A:

Q: Find the shape factor of following T section.

A:

Q: a. Determine the critical slenderness ratio of the built-up column section.  b. Determine the…

A: Welding: - It is a process in which two metals joins by using high temperature heat that melt parts…

Q: What will be the shape factor for the given section as shown in figure below? 30 mm 90 mm 30 mm 30…

A: To find the shape factor for the given section,

Q: Please show solutions on how to get the x bar only. The circle green in the figure. Civil…

A: Angle sectionDiameter of boltTo find: The value of .

Q: given truss. Pls, indicate the scale. 1000 lb 2000 lb 1000 lb 2000 lb 1000 lb D 1000 lb THE no 2000…

A: given the truss and applied load for the truss

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P…

A: P = 525 N  = 74 MPa

Q: Determine the centroid of the given composite figure. The area of the geometric figures drawn in red…

A:

Q: Locate the centroid of the composite area below

A:

Q: m y 15 cm -10 cm- 12 X

A:

Q: 6" と 90° 6" -X- 8"

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: A flat bar 10 mm thick and 100 mm wide is subjected to a pull of 100 kN. One side of the bar is…

A:

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P…

A:

Q: Find the volume of each component. 0.2m thickness

A: Given : Thickness, t=0.2 m   To Find : Volume of each Component

Q: Refer to the photo provided and please make sure your handwriting is readable. L1 = 2.02 m L2 = 1.21…

A:

Q: Determine the location of the centroid of the composite figure shown.

A: ASKED: To determine the location of the centroid of the enclosed area x, y.

Q: Y 3" 3" Determine the location of the centroid of the composite figure shown.

A: To Determine Location of centroid of the composite figure given.

Q: Define the two-elastic-layer system ?

A: Since flexible pavements are layer frameworks with quality materials on the highest point and cannot…

Q: Determine the stability and determinacy of the figures.

A: If the degree of indeterminacy is less than zero then the structure will not be stable. Otherwise…

Q: length of 6m. The beam is supported by a bearing plate of 300 mm x 200 mm x 30 mm on the wall having…

A: w24 X55length = 6mThe beam is supported by a bearing plate of 300 mm x 200 mm x 30 mmwall  thickness…

Q: Calculate the ultimate moment of the given triangular column cross-section section Mr=? Na=150 kN 90…

A: Structural steel is one of the materials which utilized for any thoughtful steel development, it is…

Q: what is the bases to cancel the kg / cm squared in correction tension?

A:

Q: 40 cm R 20 cm R 10cm

A:

Q: Mention the layer in between the beam that neither reduces nor elongated after bending.

A: A neutral layer is the layer in between top and bottom fibres of a beam that neither reduces nor…

Q: h a a The profile above depicts two joined profiles, each of width h. Find the centroid, X, of the…

A:

Q: Compute the design strength.

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Illustrate shear stresses in a cross section

A: Shear stress is defined as a stress which acts along the direction of force. It is given as τ= shear…

Q: What is the value of Q needed to determine the shear force acting on the two nails at A? 300 mm 50…

A:

Q: The thin uniform plate shown has a mass of 100 kg and is subjected to a force and couple moment…

A:

Q: The bro

A: Calculate the restrained elongation. Then using the formula for elongation the compressive load can…

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P…

A:

Q: Describe about the surface tension.

A: Surface tension is defined as the tensile force acting on the surface of a liquid in contact with a…

Q: Explain the uses of Mohr’s circle to determine stresses.

A: The equations of transformation for plane stress may be represented by a plot in graphical form…

Q: Locate the centroid of the composite area. You can choose your own reference axes. 6cm 13cm 26 cm…

A: The centroid is defined as the average position of all points in the graph or the geometric center…