A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P = 550 N. If the shear stress in the key must not exceed 82 MPa, determine the minimum dimension "a" that must be used if the key is 27 mm long. 42 mm Shear key O 7.83 mm O 8.28 mm O 11.58 mm O 9.65 mm O 6.12 mm 700 mm C Shear key detail

A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P = 550 N. If the shear stress in the key must not exceed 82 MPa, determine the minimum dimension "a" that must be used if the key is 27 mm long. 42 mm Shear key O 7.83 mm O 8.28 mm O 11.58 mm O 9.65 mm O 6.12 mm 700 mm C Shear key detail

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please show complete details, FBD, and solutions. Thank you!
Aa T Normal T No Spaci... Heading 1 Heading 2 Title Subtitle Subtle Em... Emphasis Chan Styles Font Intense E... Paragraph Styles 1. Determine the largest weight W that can be supported by two wires. The stress in either wire is not to exceed 30 ksi. The cross-sectional areas of wire AB is 0.40 in^2 and AC is 0.50 in^2 30 60° Value of TAB in terms of W %3D W1 %3D Value of TACin terms of W W2 %3D Safe value of W %3D Solution:
•Horizontal and Vertical of F •Force member BE, ED, and CD •Resultant support reaction at A -Include direction (upward, downward, N, E, W, S, or if Tensile or Compressive -Include 4 decimal points -Provide a readable solution
The lower ends of the three bars shown are at the same level before the uniform rigid block weighing 38 kips is attached. Each steel bar has a length of 2 ft, and area of 1.9 in.?, and E = 30 x 106 psi. For the bronze bar, the area is 1.4 in.2 and E = 13 x 106 psi. Determine the length (in feet) of the bronze bar so that the load on each steel bar is twice the load on the bronze bar. Bronze Steel Steel W 2 ft 2 ft
Please write the solution on paper.
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist
please show all work, thank you!
please solve and explain and neat hand writing
X= 482 show complete solutions and FBD
Hand written and clean writing
Please help me. I'll give a thumbs up
2. For the figure shown below, determine the following; (60 points) a. Maximum tensile stress b. Maximum compressive stress c. Spacing/pitch of the bolts if the shear force resisted by each bolt is 30 kN 200 mm 100 mm 30 kN/m 10 mm 20 mm |100 kN 15 kN/m 5 kN-m 150 mm C D F 20 mm 3 m 0.5 m 0.5 m 1 m 3 m 20 mm 125 mm