For the structure shown, 1. Determine the degree of indeterminacy 2. Determine equivalent statically determinate structure 3. Calculate the reactions of equivalent statically determinate structure 4. Calculate axial force, shear force and bending moment of the section 5. Draw AFD, SFD, and BMD of entire structure 6. Draw deformed shape of entire structure P P P P

For the structure shown, 1. Determine the degree of indeterminacy 2. Determine equivalent statically determinate structure 3. Calculate the reactions of equivalent statically determinate structure 4. Calculate axial force, shear force and bending moment of the section 5. Draw AFD, SFD, and BMD of entire structure 6. Draw deformed shape of entire structure P P P P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The flat truss in the figure below is under the action of three external loads P, Q and S, and is supported under pins A and B. The weight of the truss is negligible in relation to the applied loads. Read the following statements and then check the correct alternative. 1)the supports provide exactly the amount of links needed to keep the structure in balance2)the corresponding reactions involve three unknowns that can be determined through equilibrium equations.3)this is a situation where the rigid body is completely bound4)reactions are statically indeterminate which ones are correct?
Links (1) and (2) support rigid bar ABCD shown in the figure. Link (1) is bronze [E = 15,200 ksi]with a cross-sectional area of A1 = 0.545 in.? and a length of L1 = 16 in. Link (2) is cold-rolled steel [E = 30,000 ksi] with a cross-sectional area of A, = 0.400 in.? and a length of L2 = 35 in. Use dimensions of a = 13.75 in.,b = 15.75 in., and c = 20.00 in. For an applied load of P = 8 kips, determine: (a) the normal stresses in links (1) and (2). (b) the deflection of end D of the rigid bar. D P L1 |C (1) L2 b B a A X,u
4. a) Given data: F= 400 N q= 1700 N/m M= 500 Nm C1= 0.55m C2= 0.7m C3= 0.6m 4. b) Sigma x = 80 MPa Sigma z = 10 MPa Tau y = 40 MPa
For the stressed elements allocated to you, find the values and sketch the orientations:a) Maximum shear stress and the relative angle at which it occursb) Principle normal stresses and the relative angle at which they occurc) The stresses at a 40° rotation from the initial element orientationusing BOTH transformation equations AND Mohr’s circle.
A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross sectional area of 1cm?; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm? Determine the stress in the rods it p = 6 tonnes.
The stresses acting on element B (see figure part a) on the web of a wide-flange beam are found to be o = 11,000 psi in compression in the horizontal direction and oy = 2,600 psi in compression in the vertical direction (see figure part b). Also, shear stresses of magnitude Tzy = 3,200 psi, act in the directions shown. B Side Cross View Section (b) (а) Determine the stresses acting on an element oriented at a counterclockwise angle of 45" from the horizontal. Round your answers to one decimal place. psi psi psi
The state of stress at a point is the result of two loadings as shown in figure. When acting alone, the first loading produces the 3 MPa pure shear with respect of xy-axis. The second loading alone results in the 4 MPa pure shear with respect to the x'y-axis. The angle between the two sets of axis is 30° as shown. If the two loadings act simultaneously then resultant (absolute) shear stress at that point with respect to x-y axis is MPa (in integer). 3 MPa st 1 loading 2 loading 4 MPa α = 30° x'
Calculate the support responses and the bond strengths at the C-joint of the carrier system given in the figure. 6 kNm 4 KN 4 KN 4 kN/m B 1m A 4 m 6 m 10 KN +2m +2m D 3 m F
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
We are given the statically indeterminate structure shown in Figure 2. Apart from the loadings, member AB is also subjected to temperature effects. The cross-sectional depth of member AB is h = 12 in, and the thermal coefficient is aT= 5:10-6 /° F. We are also given that the effect of axial forces on the deformations can be NEGLECTED. 1 kip/ft 5 kip BV VVvvvwwW EI = 8:105 kip-ft2 EI = 106 kip-ft2 20 ft Figure 2 a) Establish a primary structure b) Establish the compatibility equation from which you will obtain the redundant force c) Determine the support reactions of the structure d) Determine the internal loading diagrams of the structure e) Determine the support reactions IF THE STRUCTURE IS ONLY SUBJECTED TO THE TEMPERATURE EFFECTS (and not the loads) AT: = 5 °F ÅT;= -5 °Fi
If the supports at A and C are flexible and have a stiffness k, determine the support reactions at A and C. The material has a modulus of elasticity of E.
A thin triangular plate ABC is fixed on side AB. The plate is strained such that all straight lines in the plate remain straight after deformation and that apex C is displaced to point C'as shown. Compute the following: a) the normal strains ex, ey and the shearing strain yxy at point C based on small deformation theory b) the normal strain at point A in the direction of AC based on small deformation theory c) the normal strains ex, ey and the shearing strain yxy at point C based on large deformation theory A 30° -200 mm. 3mm C" 1 I 1 1 60° 4mm