A quarter circular gate BP with radius of 3 mB.is shown. The bottom of the gate is submergedatadepth of2.8mandis5 mwide.Joil surface f=0.81Determine the following:a. Horizontalcomponent(indicatethedirection)of the total hydrostatic forceacting on the gate.b. Verticalcomponent(indicatethedirection)of the total hydrostatic forceacting on the gate.

Horizontal component (F) of the pressure force is equal to the projection of the curved surface on…

Answered: a. Horizontal component (indicate the…

a. Horizontal component (indicate the direction) of the total hydrostatic force acting on the gate. b. Vertical component (indicate the direction) of the total hydrostatic force acting on the gate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: From the figure shown, consider 1 unit width of gate. W.S. 6 feet 6 feet 8. Compute the horizontal…

Q: Determine the magnitude and location of the total hydrostatic force acting on a 2m x 4m gate shown

A: The values and diagram given in the question are as follows Gate dimensions=2 m x 4 m

Q: From the figure below, determine member AB.

Q: What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is…

A: Given data Oil specific gravity Water Density of block Horizontal force Normal force

Q: The gate AB is 1 m long x 2 m wide, what is the F force on the gate in kN?

A: Given: The length of the gate AB is 1 m. The width of the gate AB is 2 m. Consider the figure,

Q: The topic is all about Total Hydrostatic Force on Plane Surface. Show complete solution and…

A: Hydro-static Force: Hydro-static force is the total resultant force acting on a submerged body or…

Q: A 4.8-ft-long steel wire of 1/4 -in.-diameter is subjected to a 750-lb tensile load. Knowing that E…

A: This question is related to Strength of Material. In this question we calculate Elongated value of…

Q: Water flows in a steel pipe (ɛ = 0.00020 feet) at a flow Q = 12.5 cfs. The diameter of the pipe is D…

A: Given that: Surface roughness, ∈=0.00020 ftDischarge, Q=12.5 cfsDiameter…

Q: 3) A 4-ft high, 10-ft wide rectangular plate is hinged at the water line as shown in figure. The…

A: Width of gate =10ft

Q: A square gate shown is 6-ft on all sides is hinged at the top of the gate, and is restraine by the…

A: INTRODUCTION: This is a hydrostatic force acting on a inclined plate type question. we have to know…

Q: A 5m long, 2m wide and 2m high tank is filled with water. a. Solve the resultant hydrostatic force…

Q: Calculate the horizontal and vertical force acting on the covariate gate in the figure. Calculate…

A: Horizontal force Fh will be equal to the force on the projected area of the curved surface on a…

Q: Determine the magnitude and direction of the hydrostatic force acting on the gate using PRESSURE…

A: Hydrostatic forces on surfaces deals with the fluids i.e., liquids and gases at rest. The velocity…

Q: 2. Hydrostatic Force Find the mercury manometer reading, h, when the circular gate just starts to…

Q: 3kN/m 25KN B A 2m 4m Зт

Q: 2. The gate separating the water and gas is hinged at the top. The distance z is 12 ft. Determine th…

A: Given : Distance Z = 12 ft Determine the force that must be applied at the bottom of the gate for…

Q: The boiler has an inside diameter of 60.0 in. and a wall thickness of 1.000 in., and it is made of…

Q: A vertical rectangular gate 4 ft wide and 6 ft high, hinged at the top, has water on one side. The…

A: Consider the free body diagram;

Q: Determine the force acting on the curved part. Indicate your location

A: i have explained well through the diagram to calculate projected area , volume of fluid on curved…

Q: PROBLEM 3: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two…

Q: Given: Internal pressure of the pipe = 2.943 MPa Thickness of

A: Given data- Diameter (D) = 1 m Head (h) = 300 m Internal pressure of the pipe(P) = 2.943 MPa =…

Q: 22. Two blocks A and B with masses m and 2m are in contact on a horizontal frictionless surface. A…

A: Solution;

Q: SITUATION D. From the figure shown, consider 1 unit width of gate. ws WS. 6 feet 6 feet 8. Compute…

Q: The degree of indeterminacy for the structure is given as 24 kN E5 m w = 12 kN/m 10 m to 3A m

Q: Draw shear force diagram

A: Support reaction : ∑MC=0RAY×4-12×3+8×1=0RAY=7 KN∑FY=0RAY+RC-12+8=07 +RC-12-8=0RC=13 KN

Q: A. Calculate for the axial force in kN at member GK using cantilever method. Enter absolute value…

A: Solve using cantilever method: Assumption: The Point of contraflexure in all member lie at its…

Q: A homogeneous rectangular gate AB 6.1 ft wide and 10 ft long. Friction in the hinge is negligible.…

A: My dear Given data Width of the gate Length of gate Friction is negligible

Q: a. When are two forces equivalent? b. The beam is subjected to the system of forces and couples as…

A: Two forces are said to be equivalent if they have the same magnitude and direction, that is, they…

Q: 6ОKN 80KN 50KN 4m 2m 1m 3m W KN/m R1

A: Draw SFD and BMD We will first find reactions at support then draw SFD and BMD

Q: Compute the hydrostatic force and its line of action of the gate ABC, if the width into the paper…

A: The horizontal force Fx exerted by the water on the curved surface ABC will be equal to: Fx = γAx¯,…

Q: H.W 4 Determine the equivalent resultant force of the system and specify its location measured from…

A: To find resultant and it's location from A

Q: With the aid of diagram, define the Hydrostatic Pressure.

A: Hydrostatic pressure is the pressure, generated by the weight of liquid above a measurement point,…

Q: + 13ksi 7ksi 10ksi 10ksi 7ksi 13ksi

Q: 16. The flow of water from a reservoir is controlled by a 5-ft-wide L-shaped gate hinged at point A,…

A: Find Centre of pressureyp=3+2123=11ftForce dut to water FR=PAP=γyc=62.36ftFR=62.36ft5×12FR=22429lbf

Q: Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled,…

Q: ind the diameter of dAB BC вс + bar if the stress equal t .15GPA 120cm B 125kN 125kN 90cm A 60KN

Question

A quarter circular gate BP with radius of 3 m
B.
is shown. The bottom of the gate is submerged
at
a
depth of
2.8
m
and
is
5 m
wide.
Joil surface f=0.81
Determine the following:
a. Horizontal
component
(indicate
the
direction)
of the total hydrostatic force
acting on the gate.
b. Vertical
component
(indicate
the
direction)
of the total hydrostatic force
acting on the gate.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A semi-circular gate of diameter "d" and radius "r" is submerged in a liquid and has its diameter on the liquid surface. a. Compute for the value of eccentricity if the top of the gate is 2m from the surface and radius is 2 m. b. Compute the location of the center of pressure if the top of the gate is 2m from the surface and radius is 2 m. c. Compute for the hydrostatic force on one side 4r 13n hg CG. CP.
Comlete solution. Need ASAP. Thank you.
Need only a handwritten solution only (not a typed one).
A force of 100N is applied to the free end of a restrained beam, shown in the figure. The wall thickness is 2 mm from the upper and lower walls (1-6, 2-3, 4-5) and 4 mm on the side walls (1-2, 5-6). Calculate the normal stress distribution and the maximum stress in the middle section.
Undefined
pls help! write the solutions completely and legibly. upvote will be given! MECHANICS OF DEFORMABLE BODIES
... "H" hinge water A 1m 40KN 1.5m In the figure shown, find the depth of water "H" if the force at the bottom of the gate is 40KN to make the system equilibrium. The rectangular gate which is hinged at point A has a dimension of 1m depth and 1.5m width. A) 5.77 m B 6.27m 5.27 m No answer among the choices E 6.77 m