Determine the axial stress (kPa) in the truss member a shown in Figure 4, if the truss structure materials are hollow square section tube having a dimension of 100 mm and 5 mm thick. Also, the truss structure is subjected to a concentrated loads of 25 kN applied at the left end and 10 kN (plus quarter of the last two digits of your ID No., kN) at the middle top. Another uniformly increasing load applied in the right column of 15 kN/m (plus half of the last two digits of your ID No., kN/m). a 1.5 m 1.5 m 1.5 m 1.5 m Figure 4. Two concentrated loads applied in truss structure 4 m 1 m 1 m

Determine the axial stress (kPa) in the truss member a shown in Figure 4, if the truss structure materials are hollow square section tube having a dimension of 100 mm and 5 mm thick. Also, the truss structure is subjected to a concentrated loads of 25 kN applied at the left end and 10 kN (plus quarter of the last two digits of your ID No., kN) at the middle top. Another uniformly increasing load applied in the right column of 15 kN/m (plus half of the last two digits of your ID No., kN/m). a 1.5 m 1.5 m 1.5 m 1.5 m Figure 4. Two concentrated loads applied in truss structure 4 m 1 m 1 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find degree of static indeterminacy
Determine the vertical displacement at point B. IS KN 6 kN/m nc 2EI El EI 2.0 m 4.0 m 2.0 m Vo 8.0 m CS Scanned with CamScanner
Choose the correct answer with solution thanks! :) I need asap after 10minutes thank you.
Q8 نقطة واحدة The Bouguer anomaly over an isostatically compensated region is Zero Positive Negative Same as isostatic anomaly صفحة 9 من 12 التالي رجوع عدم إرسال كلمات المرور عبر نماذج Go ogle مطلقا. SelealjeL.University Of Misan Jalsl lio eLai ai II
I want an accurate and detailed solution
Problem Number 2 Using the slope-deflection method, draw the bending moment diagram. 3m B 2EJ 4m * 20kN/m 3m 5. Moment @ D -11.09kN-m -40.82kN-m -34.43kN-m O -24.34kN-m EJ ЗЕЈ D
100 KN/m 50 KN/m 7
↓↓ 3m 185 f 285 t 3m 3.5m compute a) Fixed-end moment b.) Distribution factors c) Moment at B fin 1.5 moment distribution t
Fluid mechanics, i need solutions in 10 minutes please. MCQ/The submerged sector gate AB shown in the figure is 1/9 of a circle radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate. A-262.874 kN B-162.328 KN C-324.260 KN D- 448.161 KN E- 591.263 KN F-392.273 kN G- 89.207 kN H-536.078 KN I-208.119 KN J- 490.984 kN K- 127.908 KN L- 113.001 KN
The following level notes for the determination of BM#2 do not check. The elevation of BM#1 and the rod readings are correct. Determine the corrected elevation of BM#2. STA B.S. H.I. F.S. ELEV. BM 1 6.72 127.36 120.64 TP 1 12.43 138.55 1.24 126.12 ТР 2 2.65 140.09 1.11 137.44 TP 3 0.54 132.59 8.04 132.05 ТР 4 4.27 124.55 12.31 120.28 BM 2 3.02 121.33
i need it ASAP please thank you
Answer the following problems using Moment Area Method