STATIOΝ B.S. F.S. ELEV. (m) BM1 9.08 150 BM1 9.08 TP1-L 12.24 3.73 TP1-H 10.10 1.60 TP2-L 11.04 2.21 TP2-H 9.92 1.08 TP3-L 1.75 9.84 ТР3-Н 0.55 8.62 BM2 11.27 BM2 11.27 A. Complete the level notes (8 pts) B. Find elevation of BM2. (3 pts) C. Find the difference in elevation BM1 and BM2. (2pts) D. Find the difference in elevation between BM1 and TP2. (2pts)

Q: p=50kN , W=90KN/m , h=7m , b=5 m

A:

Q: Question 4 a) Determine the rise in water level h as a result of surface tension between two glass…

A:

Q: SITUATION B: Prepare and complete the profile level notes for the information shown and perform the…

A:

Q: b) Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in…

A: given temp = 30 'c length = 70m size =2cm*2cm velocity = 2m/s angle = 35'c to find  given above 4…

Q: A cube of edge 24mm is resting on the top of a frustum of cone of base diameter 60mm and top…

A: In the engineering graphics we can draw both the 2 dimensional projection and 3 dimensional…

Q: Locate the centroid x of the shaded area shown in Figure 2. 16 ft - y = (4 - x ²³ ) ² 4 ft- 4 ft ↓ X

A: Given:Required:X coordinate of centroid

Q: R = 20 m %3D D = 10 m Water

A:

Q: Where must the force R be applied so that its external effect on the bar ABC F2 = 310 N will be the…

A:

Q: Determine the y-coordinate of the centroid of the shaded area. y 0.25h 68° 68° --x Answer:ỹ = i

A:

Q: Problem. The three-hinged arch supports the service load shown. The arch will tend to "kick" outward…

A: Given: A36 steel: fy = 250 MPa Solution: Free boy diagram:

Q: The stress of a structure is shown in the figure below. Assuming that the El of the entire beam…

A: To determine:SFD and BMD of frame-Moment distribution method is used for the analysis of frame

Q: Flow and spacing are inversely related O True O False

A: State true or false Flow and spacing are inversely related

Q: Find: The internal forces at point C. 0.5 ft 3 ft- 2 ft A |150 lb/ft 8 ft 4 ft -

A: We have to determine the value of internal force at point C in the given beam as per the given data…

Q: The area of the hollow part within the shaded area is 58.8 m² and the y-coordinate of its centroid…

A:

Q: *Water flows in a 0.15-m-diameter vertical pipe at a rate of 0.2 m³/s and a pressure of 200 kPa at…

A: Objective: To determine the velocity head and pressure at given elevations.   Given: Diameter of…

Q: Q4. The aluminum block has a rectangular cross section and is subjected to an axial compressive…

A: Concept: Given problem can be solved using concept of stress and strain in three dimensional…

Q: 2. Two channels are welded at the top and bottom flange to form a box column and a compact section…

A: Given,  L = 4 m or 4000 mm  K = 1  Fy = 345 MPa

Q: Solve problem 4.33.

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: Q5) Determine Ix and kx. 0.2 m 0.6 m 0.2 m y -0.8 m- 0.2 m 0.6 m

A: Moment of Inertia- We know,                          IX=∫Ay2dAlet's consider a rectangular cross…

Q: Determine the angle θ between pipe segments BA and BC.

A:

Q: Show that the complex potential f = U∞{z + 1/4a coth[π(z/a)]} represents fl ow past an oval shape…

A: Consider an oval shape, that is placed in the midway between the 2 parallel walls,…

Q: H H1 H2 Toe filter

A: Given that: Number of equipotential lines = 10                   Total head in Upstream, H1 = 12m…

Q: The moment diagram by parts are base on the moment diagram of O Fully restrained beam O Cantilever…

A: Moment diagrams by parts is a method to solve the determinate beam and find reactions in beam.

Q: Q: From the figure below, find the elevation of points A, B and C. Knowing that the elevation of the…

A:

Q: Which among the following determines the direction of closing error? O a. Tan δ = Σ/ΣΟ b. Tan 8 =…

A: A closing error is a distance that failed to close the end of the traverse line with its starting…

Q: a/2 3/2a (a 2a a a/2 Determine the coordinate of the centroid with respect to the barred axes.

A: Centroid is the average position of all the points of an object. To calculate the centroid of a…

Q: Q2) Determine the location of the centroid in the given figure. Y1 x and y required 4 m 3 m from…

A:

Q: Which among the following determines the direction of closing error? a. Tan δ = ΣD/Σ O_b. c. d. Tan…

A:

Q: 6,2 Show that Modulus of Resilience, UR 2E

A: Modulas of resilience is the amount of strain energy stored per unit volume of a body.

Q: 20 KN 30 KN 20 KN H1 5 m B D A 5 m FIGURE Q3 5 m 5 m 5 m

A:

Q: Determine the horizontal distance from Bm1 to TP1 in meters Determine Elevation of TP1 in meters

A:

Q: Given data: Pressure head%3D20 m velocity head-5 m Datum head%=2 Determine total head

A: Introduction : Total head is sum of pressure head , velocity head and datum head Given data :…

Q: Situation 6: A C3x35 has a length of 1.40 m. Fy= 248 MPa. The properties are given below. Properties…

A:

Q: Q- The staff reading taken on a workshop floor using a level is 0.645 m. The inverted staff reading…

A: Given- Staff reading of floor=0.645 m, Inverted staff reading=2.960, RL of floor=40.500 m,

Q: Activity 1. From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the…

A:

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.