Determine Rab from the circuit given below. 30 12 30 12 30 2 a o ww 20 2 ww Rab 1203 25 ২600 124 122 10 2 152 boww

Q: What will be the modified form of the codeword is even parity is used: 011010

A: When parity is used, then the parity bit is added to the left-most position of the bitstream.  In…

Q: I, I. The values of E, R, and I are given on the Student Values Spreadsheet. Give the values of I1…

A: Given circuit, Where, E = 62 VR = 31 OhmI = 87 A

Q: Explain the successive approximation

A:

Q: _is algebraic difference of the upper and lower limits of the range Span Range Precision O Accuracy

A: Span , range , precision and accuracy are common terms use in measurement.

Q: it is called as the difference between the value and the measured value of a quantity a. mistakes b.…

A: In this value we will find significant figures...

Q: Which of the following characteristics belongs to an analog quantity? a. Its values follow a…

A: The solution is given below

Q: Electronic What is Polymorphism. What is Mailbox.

A: The System Verilog provide dynamic array construct. In packed array one location and whole location…

Q: emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a)…

A:

Q: Mark the correct definition - Analog electronic measuring instruments - the physical quantity,…

A: Analog measuring instruments takes input as analog signal process it in analog fashion amd gives…

Q: Identify the no. of positive numbers and zeros from the list of numbers. The length of the list is…

A: Length of list stored  AT 2200H. Series begins from ML 2201H. Result to be stored  in ML 2300H and…

Q: The FDMA channel carries phone circuit at a time. a) Ten b) Two C) One d) Several

A: FDMA stands for Frequency Division Multiple Access. Bandwidth of FDMA channels are relatively low.…

Q: (a) Describe the following metrology terms: i. Accuracy ii. Uncertainty iii. Calibration iv.…

A:

Q: . Determine the truth table of the digital çircuit shown in the figure below and explain its…

A:

Q: Choose the correct ray diagram for a convex lens. Object Object F F Image s' F Image

A:

Q: 3. a. An ammeter reads 3.53 A, with an error of 2%, then determine the true value of measurand and…

A: Given: An ammeter reads  3.53 A, So, measured value, Im = 3.53 A, With an error, %ε = 2%.

Q: Explain ethics in your own words in the engineering field.

A: Engineering ethics is defined as the field of applied ethics anda system of moral principles that is…

Q: Explain any four dynamic characteristics of measurement system.

A: The explanation is as follows.

Q: ) Define quantitative and qualitative data.

A: a) Quantitative data:-            Quantitative data are measures of values or counts and are…

Q: Describe the general process for “digitizing” audio and image data. Be certain to reference the…

A: Digitization is information like the object, text, image, audio is converted into a single binary…

Q: Digital communication system can handle a) Analog signals b) 1D signals c) 2D signals d) All of the…

A: The correct answer is OPTION D

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: Q2: (A)Find the following: 1- (110)10+ (0111)2.by using BCD numbers. 3-(3E91)16- (1F93)16by using…

A: The number system is used to represent information in digital electronics. Different bases exist in…

Q: • SuperNe liı. A moodle.nct.edu.om Convert the octal NUMBER 2713. 6464 to hexadecimal number showing…

A: Answer; 5CB.D34

Q: Give the drain current equation of JFET.

A: The output characteristic of a JFET is shown in the figure below:

Q: 8. Members of WTO are required to a. Eliminate all tariffs b. Enforce patent rights for patent…

A: 8>WTO or world trade organization is an intergovernmental organization which is used to…

Q: Suggest the transducers/elements that might be considered for the measurement systems to be used to:…

A: Transducer-  Transducer is an electronic device which is used to convert one form of energy into…

Q: agram. [Note: write maximum 10 sentence, not more than that]

A: Given: ADC and DAC is shown as:

Q: Show the difference between the Accuracy, Precision, and Resolution with definitions and examples.

A: Accuracy: It is the closeness of the result/output of the measurement to the actual value Precision:…

Q: Logic

A:

Q: i- Draw the V-I characteristic curve of a Thyristor/SCR device. ii- Describe this V-I characteristic…

A: SCR is the widely used in Power electronics for controlling the large power. SCR is silicon…

Q: 12V You To=3 P= ? re si I= ? P= ?

A:

Q: differentiate NEUTRAL, EARTHING, and GROUNDING.

A: According to the question we have differentiate NEUTRAL, EARTHING, and GROUNDING.

Q: QUESTION 46 HIRF is? A strong transmitted electromagnetic field. O The ability to detect…

A: Note: As per our policy we can solve only one question, please reupload the remaining question as…

Q: 4. Which of the following can't be included in data required for coordination study? a) X/R Ratio b)…

A: as per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: 5. What are the advantages of Centre tapped and Bridge Rectifier?

A: Various loads work on DC, but the supply available to us naturally is AC supply. Rectifier is a…

Q: Calculate the sum of series of odd numbers from the list of numbers. The length of the list is in ML…

A: GIVEN: Calculate the sum of series of odd numbers from the list of numbers. The length of the list…

Q: Q. With meaningful examples of your own write down usage of all the c. Communication commands

A: Communication commands find use in network data transfer and analysis.

Q: . Write the difference between the MOSFET and IGBT?

A: IGBT MOSFET Stands for Insulated Gate Bipolar Transistor Stands for Metal Oxide Semiconductor…

Q: Explain Transducer classification adding EXAMPLE to each category.

A: Transducer - A transducer is a machine that, when activated, converts one form of energy to another.…

Q: Q28 The accuracy of digital meters is more than analogue meters.  True  False

A:

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.