Determine I, and I, for the region shown. Note that the region is symmetric about the x-axis. 68 mm 17'mm 18'mm 17 mm 27 mm

Q: Find the location of the centroid of the following shape: 90 mm 30 mm 70 mm X k 30 mm 30 mm y n…

A:

Q: When a rigid body is subjected to curvilinear translation, not all the particles of the body travel…

A: A body is said to be rigid only when there is no change in the relative positions of the particles…

Q: Both portions of the rod ABC are made of an aluminum for which E= 70 GPa. Knowing that the magnitude…

A: Given : E = 70 GPa This is a problem of solid mechanics where we are asked to determine : a) The…

Q: Please recheck Ra and Rb is actually equal to 6kn and not 15kn

A: As per the given question, we have to check the reactions at supports. Original question was: A beam…

Q: Please calculate the deflection-y at point 5, and the deflection-x at point 2 based on the following…

A: ####Calculation of deflection Y at 5 and Deflection X at 2 Using Unit load Method of Analysis ####

Q: Let a = [a] mm. Each segment has a thickness of 10 mm. f) Determine the y-coordinate of the…

A: Determine the y-coordinate of the centroid.

Q: the location of the centroid from the y-axis is equal to

A:

Q: If the Force of members AB, AC, and BC is 7kN, 6.06kN, and 0.37kN, what is the magnitude of the…

A: Given Data  Force in member  FAB = 7 KN  FAC = 6.06 KN  FBC = 0.37 KN  Find force in member CD and…

Q: 1 = l2 The radius is (mm) 100mm

A: Given:- Ix1=Ix2 To find:- radius

Q: Solve the centroidal  Ix Solve the centroidal Iy Solve the Ix and Iy

A: Consider the figure,

Q: 5 Find the centroid of the following structure. (20 2.5" dia hole- centered 4" 5" 3" 4" 6" 3"

A:

Q: A rod of homogeneous thickness shown in the figure is AB length L and BC length 2L. Find the angle…

A:

Q: ) The x−coordinate of the centroid for this shape is located: To the left of the ?−y−axis…

A: In the given question figure

Q: Determine the single force that will replace the following coplanar forces Force Degrees from X (N)…

A:

Q: A beam is subjected to equal bending moments of M₂ = 2800 N.m. The cross-sectional dimensions are b…

A: The bending moments of Mz = 2800 Nm. The cross-sectional dimensions are b = 150 mm  c = 27 mm d = 72…

Q: (a) (c) Question 7 The vertical deflection of node C for the truss shown in figure is 2 PL AE PL AE…

A:

Q: A uniform bar of length L, cross-sectional area A, and unit mass p is suspended vertically from one…

A:

Q: Every ___ of a linearly dependent set of vector is linearly dependent

A: Every superset of a linearly dependent set of vectors is linearly dependent, and every subset of a…

Q: F 4 m 2 m 1.5 m 2.5 m 2 m 1 m 0.5 m B The assembly above consists of straight members forming a…

A: Given that:            Unit vectors for members AC and AD:          uAC=0.707i-0.707j…

Q: Ma 20KN 5m RA RB

A: Conjugate beam Method: This is one of the methods which is used for determining the slope and…

Q: The profile above depicts two joined profiles, each of width h. Find the centroid, X. of the total…

A:

Q: moment of inertia of the section about the x’ axis.

A: Given figure dimesions are there and the centroid and moment of inertia are to be calculated

Q: 3. Determine the centroid of the lamina shown in Figure -100 mm- -20 mm 25 mm 70 mm

A: To find out the centroid of the lamina?

Q: Determine component of all forces DEF and ABC for the frames shown in Figure 0.3 m 0.2 m с 0.25 m…

A:

Q: Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully…

A: To find centroid

Q: 5) 9: x+ Cx +Cze*

A: Answer (5) We know that the elimination of arbitrary constants is done by differentiating the given…

Q: 7'

A: Given that :-                       In this question we will use the following formula to calculate…

Q: Determine the z-coordinate of the mass center of the homogeneous paraboloid of revolution shown…

A:

Q: (5) When calculating the global stability of the beam, @s should be replaced by o's when the global…

A: For global stability of the beam, φb should be replaced by φb when the global stability coefficient…

Q: number of significant digits; the tolerance is +_1 in the third significant digit

A: The given measurements are 9 mm, 12 mm, 22 N, 38 mm, 26 mm, 23 mm, -71 mm, 22 N. These measurements…

Q: 16 cm 8 cm 8 cm 8 cm -X

A:

Q: e general solution

A: Given:- (4D5-23D3-33D2-17D-3)y=0 To find:- general solution

Q: Evaluate the degrees of indeterminacy for the frames shown below. (a) (b)

A: Given data:- (a); (b);