Answered: Design the beam shown in figure using…

Design the beam shown in figure using ultimate strength method, f, = 28 MPa, f, = 400 MPa. L. L. - 20 kN T D. L. - 10 kN/m h 500 mm 2 m - F350mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The load is supported by the four 304 stainless steel wires that are connected to the members AB and…

A: We have given the following data :

Q: From the figure shown, determine the following: a. The plastic moment of the whole beam. b. The…

A: The given structure is a continuous beam with hinged supports. It is asked to find the plastic…

Q: Calculate the ultimate moment capacity of a rectangular beam with b = 350mm, d = 540mm, A, =7- 28mm.…

A: Given, b=350 mm d=540mm As=7-28 mm f'c= 24 MPa fy=345 MPa

Q: Q: Verify that the steel seetion W12 x 106 can be used for the cantilever beam shown in the Figure.…

A: The deflection in the beam is a horizontal member of the building or structure which goes under…

Q: 3) The simply supported beam with the cross-section as shown supports a total uniformly distributed…

A: Allowable tension flexural stress = 35 MPa Allowable compression flexural stress = 150 MPa

Q: The frame given in the figure R = 0.25m radius at point E a frictionless reel are available. Support…

Q: From the given figure below, determine the minimum height of the beam if the flexural stress is not…

Q: 91 lb/ft A В l, ft l, ft Determine the internal loads diagrams of the beam above. In the cell bellow…

Q: 2- Calculate the design ultimate load Wu on the on the beams B1,B2, B3, B4 3.6 m 4.8 4 m Assume: DL…

Q: 30MINS

Q: For the inverse T-section beam that loaded as shown in figure, find the maximum tensile and…

A: A double overhanging beam is given we need to find out maximum tensile and compressive bending…

Q: to prevent excessive deflection of a cantilever steel beam, a tension rod is attached to its end. -…

A: 3x 3Cantilever Beam with UDL= 2kN/m & point load of 3 kN (upward) Vertical Reaction at Fixed…

Q: The cantilever beam shown in figure (2) supports the roof of a workshop shed "no-ceiling". Design…

A: l = 18feet = 216inch w = 1.3 + 2.7 = 4kip/ft M = wl2/2 = 4 x 182/2 = 648 kip-ft Let the material be…

Q: Determine the design moment strength of the T-beam. Use fr=20.7 MPa and fy=414 Mpa.

A: Answer we are given f'c = 20.7 Mpa fy = 414 Mpa As = 2-25 mm As = 2 * π4*252 As = 981.75 mm2…

Q: 3- For the beam given in the figure, a- Draw the elastic curve by using the Mohr Method. b-…

A: Given data:- Beam given is below figure;

Q: Determine the force of member BD. Include a negative sign if the answer is in compression. Indicate…

Q: by 늘 wo B 늘 C X

A: Given Data:Length L=6.3md=300mmbf=215mmtf=14mmtw=10mmIt is required calculate the largest intensity…

Q: A cantilever beam of 7.2 m span is a part of a floor supporting a concrete hollow block partition.…

A: Deflection : The degree to which a component of a structural member is shifted under a load is known…

Q: A beam is loaded as shown, with a force P = 300 N and length L = 1.25 m. The material is steel AISI…

A: P = 300 N L =1.25 m CROSS SECTION = 15 mm by 15 mm TO FIND : REACTION , MAXIMUM BENDING MOMENT,…

Q: For the beam shown below: a) Calculate the elastic curve equation Ely Mo A = R³L 6 Mox³L + cx + C₂…

Q: EX3: For the beam shown in the figure below. Find maximum allowable ve load(P)that the beam can…

Q: art 1 The simply supported beam below is initially designed to undertake a concentrated factored…

A: According to given data

Q: The beam ABC shown in given figure is horizontal. The distance to the point of contraflexure from…

A: Given data, The distance to the point of contra flexure from the fixed end A

Q: Determine the force in each member of the truss shown by the method of joints. Show free body…

Q: The sketch below represents an ordinary flat roof of a building. The beams support the roofing…

A: GIVEN- The roof supports a live load of 40psf- F.B.D of beam A-H showing loads on it.

Q: Design the steel reinforcement for flexure for the rectangular tapered beam to carry the loads shown…

A: Live load, LL = 20 kN/mcover = 75 mmwidth, b = 380 mmHeight at the fixed end, hf = 800 mmHeight at…

Q: Q2// The beam in Figure 1 is made of 2024-T4 aluminum alloy (E = 72.0 GPa, oy = 330 MPa, o= 470 MPa,…

Q: What is the horizontal support reaction RAX at support A for the ?frame shown below 35 kN/m B 15 m A…

Q: Compute and Design the beam loaded as shown. 20 kN/m 10 kN/m 15 kN 5m 4m The im f'c = 20.7 MPa fs =…

A: The total load on the beam can be calculated by adding the distributed loads and the point load. The…

Q: 1- Calculate maximum deflection of the beams. 2- Check the suitability of the section assuming the…

A: UKB 457 x 152 x 82 I = 366,000,000 mm4 E = 2 x 105 FIND1- Calculate maximum deflection of the…

Q: 3. The beam and loading shown in figure below, is a simply supported beam with a span of 7.2 m and…

A: Given that :-a simply supported beam has following specifications :- a) span = 7.2 mb) the service…

Q: For the given properties of the b determine the safest wy that th bf = 850mm

Q: Quiz: Design the reinforcement steel that necessary for the shear and torsion for the rectangular…

A: Solution; Given that; Live load=10 KN/m2Dead load =5 KN/m2fck=26MPafy=400 MPa

Q: A simply supported beam is 4m long and has a load 200 kN concentrated at middle. The flexural…

A: A simply supported beam, Length = 4mConcentrated load at middle point = P= 200kNEI= 300MN-m² =…

Q: For the beam(300x800mm) to carried the loads shown in the figure below,design the steel…

A: Given values: Size of beam: (Width b * Depth D) = 300 * 800 mm Span = 9 m f'c = 25 MPa fy = 414 MPa…

Q: 3) The simply supported beam with the cross-section as shown supports a total uniformly distributed…

Q: Need help asap pls. The beam is shown below. The cross-section of the beam is 250 mm x 400 mm. Take…

A: Given Data E = 200 GPA Cross section of beam 250 mm × 400mm Find 1. Deflection at right end of…

Q: Compute the loads and deflections point D at each yield and the ultimate level for the structure…

A: The forces are the amount of loading that happened on the area required by the specimen. The…

Q: Strictly show all of the free body diagrams used upon solving the problem. Complete solution is a…

Q: 600 N/m 600 N/m 2 m 1 m 2 m R1 R2 Find the deflection at mid-span

A: To find the deflection at mid-span, using the double integration method. In the double integration…

Q: From the figure shown, determine the following: a. The plastic moment of the whole beam. The order…

A: Solution: Find the actual plastic moment: The mechanism for span AB: The maximum moment will occur…

Q: A 150mm x 25mm wooden beam is reinforced with two 10mm thick steel plates on the top and bottom…

Q: Find the length of cantilever beam to carry the loads shown in the figure below: D.L= Self weight,…

A: Section is uncracked, To determine the length, L of the cantilever beam. Taking unit weight of…

Q: For the flat plate shown in the figure below (edge beam are not used), design the hatched frame…

A: According to the question we have to design the middle and column strips of the hatched slab in N-S…

Q: Given a 9.8 m column pinned at the top and fixed at the bottom with the following properties: Fy =…

Question

Design the beam shown in figure using ultimate strength method, f = 28
MPa, f, = 400 MPa.
L. L. = 20 kN
D. L. 10 kN/m
B
500 mm
2 m /
-6.0 m
F350mm"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A column 3m long and pinned at both ends carries an axial load of 190 KN. The column is made up of two-angles of unequal legs with long legs back-to-back and separated by gusset plate whose thickness is 1 Imm. Use A50 steel with Fy=248 MPa, Fu=415 MPa and E=200 GPa. Three sections are being considered, as follows, with their respective properties relative to this problem (all units are in meters). Section 21 125 x 75 x 12 I. (m) 0.0390 1, (m) 0.0160 Area (m) 0.00454 0.00463 0.00550 21 150 x 90 x 10 2L 150 x 90 x 12 0.0480 0.0500 0.0195 0.0251 a. Which of the sections gives the largest allowable compressive strength? b. Which of the sections gives the smallest compressive strength? c. Which of the sections gives the most economical section for the given load?
A horizontal beam ABC is loaded as shown in the figure below. The distance of the point of contraflexure from end A (in m) is 10kN (327) Ag 0.75m B C k D 1m -
Please solve the question below step by step A) Draw the shear and moment diagram. Determine and label where is the critical point occurs. B) Calculate and show that the beam is safe and can withstand the load. ( List down all the assumption made ) C) Explain the function of the beam as shown in figure.
Q7/ A simply supported beam of cross section shown in figure supports a uniform load over a span of 5 m. Use the data below to find: A. Allowable live load can be carried by this beam. B. If the uniform live load = 50kN/m, can the beam carry the applied 2016mm load? 4020mm Data: f = 28MPa, fy = 350 MPa, y = 24, D. L = self weight Ans. L.L=36.6kN/m 300 009
ASAP dont round off initial values, round off final ans only
The loads on a bcam section are shown in the figure bclow. Determine whether the beam is adequate to support the loads. f =24 MPa and f, = 420 MPa. *300 mm- L= 60 kN D =13 kN/m. (excluding weight) 4-D25 5 m 0000 - unu 00S 425 mm
Q3/ A rigid beam ABCD shown in Figure with negligible weight is pinned at one end and attached to two vertical rods. If the beam is subjected to load of P=60 kN. Find the vertical movement at D. Aluminum A- s mm Steel E- 68000 MP L-2 A-300 E- 200000 MPa D 60 KN | Im Im IIm
i need clear ans and solve very very fast in 20 min and thank you DYBALA .: For the composite structure shown in Figure, using unit load method (virtual work method), find the vertical deflection at B ( AVB), use El=100,000 kN.m2, AE 10,000 kN. A 10 kN/m AAAAAAA 6m B 6m D Link 3m C
3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 1m IC 4P 3m D 2P 1m DE U 175 200 (Dimensions in mm)
USE NSCP 2015
A W 150 x 24 steel column is 8 m long and is fixed at its ends as shown in Fig. Its load- carrying capacity is increased by bracing it about the y-y (weak) axis using struts that are assumed to be pin connected to its midheight. Determine the load it can support so that the column does not buckle nor the material exceed the yield stress. E=200 MPa and Fy = 410 Мра. w mmh m 4 m 4 m LE (Ctrl)
The I-beam section shown below is simply supported over a span of 6 m, what is the service uniform live load it can carry if the total dead load including beam weight is 12 kN/m? Use d = 700mm, f = 21 MPa and fy = 420 MPa. 100 3-025 -300- 100 540 120 760