Data for yield stresses of reinforcing bars in MPa have been presented in terms of frequency distribution below. Represent these data graphically in terms of histograms, frequency polygon, and ogives. Table 2.3-12: Frequency table for yield stresses of reinforcing bars in MPa. Classes Frequency 350 365 1 365 380 1 380 395 2 410 425 395 9 410 8 425 440 8 440 455 9 455 470 1 470 485 1

Data for yield stresses of reinforcing bars in MPa have been presented in terms of frequency distribution below. Represent these data graphically in terms of histograms, frequency polygon, and ogives. Table 2.3-12: Frequency table for yield stresses of reinforcing bars in MPa. Classes Frequency 350 365 1 365 380 1 380 395 2 410 425 395 9 410 8 425 440 8 440 455 9 455 470 1 470 485 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Detailed Handwritten solution required. This is multiple choice question.
During a tensile test on a specimen the following results were obtainedload(KN) 15 30 40 50 55 60 65 70 75 80 82 80 70extension(mm) 0.05 0.094 0.127 0.157 1.778 2.79 3.81 5.08 7.62 12.7 16 19.05 22.9diameter of gauge length=19mmdiameter at fracture=16.49mmgauge length=100mmgauge lengthat fracture=121mmplot the complete load extension graph and the straight line portion to an enlarged scale .hence determinethe modulus of elasticitythe percentage elongationthe percentage reduction in areathe nominal stress at fracturethe actual stress at fracturethe tensile strength
Need the correct handwritten solution , Don't make any mistakes
5) Given the stresses shown at an arbitrary point, calculate the principal stresses and the max shear stress (15 Points) бу = 100 MPa H L C # DELL O Ⓡ 7 88 Txy = 55.9 MPa √x=200MPa
Please answer this quick
Refer to the given figure: Find: a) Determine the average bearing stress between the bolt head and the wood.b) What is the maximum diameter of a hole can be, if the hole is punched from a plate that has its maximum shear stress at twice its maximum crushing stress? *p = width*
i need the answer quickly
5/Determine the smallest value of uniform load that will cause a crack for the reinforced concrete beam shown below. Use f= 30 MPa Wer=? 3.6 m- Ø16mm 100 600 100-> 100 200 50
Determine modulus of elasticity if bulk modulus 75 MPa and value of poisson ratio 0.32
Problem # 2: The frame carrying a 384-kg load is supported by roller at D and smooth pin at A. Assuming double shear in all pin connections, calculate the pin reaction at E and shearing stress developed in the pins at B andC. Use a pin diameter of 16 mm in all connections.( 2.8 m- t19 m- A 下 1.5 m 0.5 m 0.5 m T B 1.6 m 1.5 m 384 kg
Asapp.
Q1)The magnitude of stresses have been applied on soil element where Normal vertical stress is 120 KN/m² , Normal horizontal stress is 300 KN/ m², shear stress is 40 KN/m² and Angle of internal friction is 20°. Find the Principle stress and Normal and Shear stress on plan AB, figure 1. The figure 1 is below i have attached in jpg format. Solve the question according to this figure?