Determine the deformation of the steel rod (inches) in the figure shown under the given loadsGiven: A1 = 0.94 in2, A2 = 0.38 in2, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psiYour final answer should have three decimal places Determine the deformation of the steel rod (inches) in the figure shown under the given loadsGiven: A1 = 0.94 in2, A²? = 0.38 in², P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psiYour final answer should have three decimal placesA2A1|A | BP3P1P2-16 in.-12 in.12 in.

Answered: Image /qna-images/answer/042ff16b-3843-4b5a-959f-33292fcf449b.jpg

Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A² = 0.38 in?, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places A2 A1 |A B P3 P1 P2 16 in. 12 in. 12 in.

Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A² = 0.38 in?, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places A2 A1 |A B P3 P1 P2 16 in. 12 in. 12 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is constructed of two angle sections, each L5 x 3 x 1/2, which reinforce a 2 x 8 (actual dimensions) wood plank (see the cross section shown in the figure). The modulus of elasticity for the wood is E, = 1.2 x 10° psi and for steel is E, = 30 x 10° psi. Assume that the component parts of the beams are securely bonded by adhesives or connected by fasteners. Also, use the transformed-section method in the solutions. 2 x 8 wood plank 5 in 3 in. Steel angles Find the allowable bending moment Mallow for the beam if the allowable stress in the wood is Ow = 1300 psi and in the steel is o = 10,500 psi. Dimensions and properties of the angles: I, = 9.43 in.*, d = 1.74 in. and A, = 3.75 in." (Note: Disregard the weight of the beam). Round your answer to one decimal place. Mallow = k. in.
The maximum allowable tensile force in the members of the truss is (Ft)max = 1700 lb, and the maximum allowable compressive force is (Fe)max = 1000 lb. (Figure 1) Figure 1 of 1 Part A Determine the maximum magnitude P of the two loads that can be applied to the truss. Take a = 8 ft. Express your answer in pounds to three significant figures. P = Submit Provide Feedback Π| ΑΣΦ ↓↑ vec Request Answer C ? lb
At a temperature of 37.4 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 128.7°C, determine the change in length of the steel rod if L = 328.25 mm and M = 215 mm. Round off the final answer to four decimal places.
Example 21.18. A solid circular steel rod 6 mm in diameter and 500 mm long is rigidly fastened to the end of a square brass bar 25 mm on a side and 400 mm long, the geometric axis of the bars lying along the same line. An axial tensile force of 5 kN is applied at each of extreme ends. Determine the elongation of assembly. For steel E = 200 GPa and for brass E₁ = 90 GPa
Item 7 The members of the truss are assumed to be pin connected. (Figure 1) Figure 1 of 1 12 ft 44 -16 ft 16 ft P P 16 ft Part A If member AB is an A992 steel rod of radius 2.5 in., determine the maximum load P that can be supported by the truss without causing the member to buckle. Express your answer to three significant figures and include the appropriate units. μА P = Value kip Submit My Answers Give Up ?
Can you help me to solve this question please ? Thank you!
The adjacent sketch indicates a brass wire which is exactly 12.00 m long and a steel wire which is 12.01 m long. Each wire has a cross-sectional area of 150 mm2 . What load does each wire carry if E steel = 200,000 MPa & E brass = 110,000 MPa? (Hint: no load on steel wire until brass wire stretches by 10mm, then ratio of stresses in each wire is same as ratio of E v
Please show solutions on how to get the 0.75 value. The circle green in the figure. Civil engineering- steel design
Please solve. Show your solution on a paper with FBD
Please limit your answers to four decimal places and should be expressed without constants.
2:37 20.0 KB/S docs.google.com/forms 55 Write down your year and section. * Your answer Problem 1: The rigid bar AB is attached to two vertical rods as shown. If P=50KN, determine the vertical movement of points A and B. Your answer Figure for Problem 1 ALUMINUM L=4M A=50OMM? E=1OGPA STEEL L=3M A=30OMM? E=20OGPA A 2M 3M B -.
Part A In (Figure 1), r = 30 mm. Locate the centroid a of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. T = 0 mm Submit Previous Answers Correct Figure < 1 of 1 Part B Locate the centroid ī of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. HẢ ? 150 mm = Value Units Submit Previous Answers Request Answer 50 mm 100 mm 100 mm 50 mm