A bar specimen of 36 mm diameter is subjected to a pull of 90 kN during a tension test. The extension on a gauge length of 200 rum is measured to be 0.089 mm and the change in diameter to be 0.0046 mm. The Poisson's ratio will be the

Q: ст ג'Tיוידי 61 Value: mm Value: cm 1 2 3 4 5 6 7 8 9 10

A: The main scale reading = 5.4mm Coinciding vernier division, (CVD) = 1Least count = 0.01mmThe vernier…

Q: 1) Compute the centroid y bar with respect to its base.

A:

Q: Problem 2: Determine the centroid X-bar with respect to Y-axis -150 mm 15 mm C 150 m -15 mm 15 mm…

A:

Q: Determine  kinematics  indeterminacy

A:

Q: Determine the y-coordinate of the centroid of the shaded area. y 0.30h 58° V 58° -x

A: From the geometry,tan32o = ABh ⇒ AB = 0.62hSo, AC = 0.62h + 0.62h = 1.24htan32o = EF0.3h ⇒ EF =…

Q: Prepare a summary for usage of flood barrier during flood.

A:

Q: ) Determine AT 2.) Determine Centroid about y(x) 3.) Determien centroid about x (y)

A:

Q: 44m 115 m 700 20m 100m 66m

A:

Q: Soo > 100 - Azz SOo X (0030 AT = Soom Tioom Soum 100m Ioom 100m 200 M

A:

Q: Determine the y-coordinate of the centroid of the shaded area. y h 0.35h / 70°y 70° Answer: ỹ =

A:

Q: Q.: Find the coordinate of the centriod of the shaded area 4 Y 3 m-

A: Given, Equation y=2x-30.5

Q: Derive the relationship for maximum and minimum shear stress in a wide flange I-Section. Also…

A: Given: V=50KNflange width=300mmflange depth= 40mmweb thickness=40mmweb depth=220mm   Calculate the…

Q: Calculate the y-component of the centroid of the area shown. 5 5 8

A: we will calculate centroid by using each section.

Q: 1. What is the value of ybar from the 1-1 line [ Select ] 2. What is the value of centroidal MOI…

A:

Q: B LA "' 11 1 il 11 il || U B N Fig. 5-5-L Matching test. R 13 NO DE 17 21 S W AL 14 CASA 18 8 HA n…

A: To Match the Orthographic projections with the isometric ones

Q: is required to find soil pressure at a depth of 10 ft beneath the interior corner A and exterior…

A:

Q: Determine the y-coordinate of the centroid of the shaded area. y 0.25h 68° 68° --x Answer:ỹ = i

A:

Q: Locate the centroid of the line ABC.

A:

Q: Add 1 cm and 1 m A. 50 cm B. 101 cm C. 250 m D. 150 m

A: Given data : 1 cm , 1m Since , we know that : 1m = 100cm

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Y T 0.62 al IK Answer: (x, y)…

A:

Q: Determine the y-coordinate of the centroid of the shaded area

A:

Q: 400 15/11 ि 5' RAy = ● RAY = RBy = A * 100016 d 5' * T 5' 500lb 0 B xZi *

A: Hinged support has two reactions in the x and y directionRoller support only has one reaction in Y…

Q: cubjected to a tensile load P by pins at A and B Is shown in Figure P3.4. The width of the bar is v…

A: P=17.4ksi W=2in To find poisson's ratio and modulus of elasticity

Q: Find the centroid and moment of inertia of the cross-section 275 mm Ref. Origin 50 mm 75 mm 50 mm…

A:

Q: SITUATION: Refer to Figure below. Point loads of magnitude 500 KN, 750 KN, 800 KN, and 1000 KN act…

A:

Q: 1- Locate the centroid of the area ABC. For the shaded area x= y = x = y = For the perimeter A 240mm…

A: Since the given figure is symmetrical about the y-axis.Therefore, the centroid will be;Compute the…

Q: y 74 mm 36 mm - 36 -+ 36 mm mm Answer: y = i mm

A:

Q: す 20 = 707 Ks 707 kj - 10 = .707 ks

A: To find value of KJ and KD

Q: Q. locate the Centroid for the following areas: y 4 0.3m 0.3m 0.5m ++ 0-43 0-2m Figure (2) Note:…

A: Figure is as shown

Q: origin: center of quarter circle R2 calculate: total area (mm2) centroid along x axis…

A:

Q: A beam of circular cross section is 3000 mm long and is attached at each end to supports which allow…

A: L = Length of beam = 3000 mm = 3 mP = Offset load = 40000 N = 40 KNσy = Yield stress = 145 N/mm2

Q: On Step 3 where do you get the sin(66.80)? reply asap.

A: Required:Explain sin(66.80) in step 3

Q: 2 1 Matrix -1 + 2 Matrix 1 3 -2 4 A. Matrix 2 2 B. Matrix 1 1 C. Matrix -1 D. Matrix 1 5 2.

A: Given:- Two matrices are given:- A = 21-13 B = -1211 To determine:- The value of Matrix 21-13 +…

Q: H, = 19 mm, G, 2.51, Pa 1.73 g/cm d, = 0 division, Gauge factor = 0.01 (mm/division) Dial Gauge Dial…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…