A 0.625 in. thick rectangular alloy bar issubjected to a tensile load P by pins at A and Bas shown in Figure P3.4. The width of the bar isw = 2.00 in. Strain gages bonded to thespecimen measure the following strains in thelongitudinal (x) and transverse (y) directions: &= 1,140 µɛ and &, = -315 µɛ.(a) Determine Poisson's ratio for this specimen.(b) If the measured strains were produced by anaxial load of P= 17.4 kips, what is the modulusof elasticity for this specimen?EyType here to search38°F Mostly clear90 Homework 02AyBFIGURE P3.4

P=17.4ksi W=2in To find poisson's ratio and modulus of elasticity

cubjected to a tensile load P by pins at A and B Is shown in Figure P3.4. The width of the bar is v = 2.00 in. Strain gages bonded to the pecimen measure the following strains in the ongitudinal (x) and transverse (y) directions: & = 1,140 a) Determine Poisson's ratio for this specimen. b) If the measured strains were produced by an xial load of P=17.4 kips, what is the modulus felasticity for this specimen? and &, = -315 µɛ. ere to search 38°F Mostly cle 90

cubjected to a tensile load P by pins at A and B Is shown in Figure P3.4. The width of the bar is v = 2.00 in. Strain gages bonded to the pecimen measure the following strains in the ongitudinal (x) and transverse (y) directions: & = 1,140 a) Determine Poisson's ratio for this specimen. b) If the measured strains were produced by an xial load of P=17.4 kips, what is the modulus felasticity for this specimen? and &, = -315 µɛ. ere to search 38°F Mostly cle 90

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 60 MPa, σy=σy= 80 MPa, and τxy=τx⁢y= 42 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 72 GPa and v = 0.29 for the machine component.
The thin square plate shown is uniformly deformed such that , +1.360 ut. , -628 ut, and y=+1.285 urad. Determine the normal strain ,, in the plate. 60 mm -276 με Ο 351 με -179 ut -254 HE -233 με x
Please solve correctly
A tension test is being conducted on a steel-rod specimen with a gauge length of L0=2 in and initial diameter of d0=0.5 in. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 74.0 ksi, e = 104.0 ksi , g = 85.0 ksi , and h = 0.15 in/in. Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 2.7 in . Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 11.0 kips, find the nominal stress experienced by the rod. Determine the force P needed to reach the ultimate stress in the steel-rod specimen.
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
Problem 2: Analyze the following, state the determinacy and the stability. 3. 2. - hinge hinge hinge-
Problem 03
In a strained material stresses are given below sigma_x=100Mpa & sigma_y=-50Mpa txy=30Mpa.Calculate total strain energy, volumetric strain energy, shearing strain energy. E=2.1×10^5Mpa & mu=0.28
The yield strength of 5 steel specimens was determined using the uniaxial tension test. The mean value of the yield strength is 29 ksi. If the sample standard deviation is 2 ksi, the 95% confidence interval for the yield strength of steel is: A. (26.5ksi, 31.5ksi) B. (25.7ksi, 31.3ksi) C. (27ksi, 31ksi) D. (25ksi, 30ksi)
At a particular point in a structural member a direct tensile stress of 60 N/mm² exists on a plane perpendicular to the longitudinal axis of the member while a direct compressive stress of 40 N/mm? occurs on a plane parallel to this axis; in addition shear and complementary shear stresses of 50 N/mm? act on these planes. If Young's modulus E is 200000 N/mm² and Poisson's ratio v is 0.3 calculate the direct and shear strains on these planes and hence, using a graphical method, determine the principal strains at the point, the maximum shear strain and the angle the plane of maximum principal strain makes with the longitudinal axis of the member. Finally, calculate the principal stresses at the point. Ans. E= 3.6x104, ɛ, = -2.9x104, Yy=6.5x10-4 ɛ1 = 4.95x10, 01 = 80.8 N/mm², o1=-60.8 N/mm. Ɛ11 =-4.25x10 Ymax=9.2x10-, 67.5°
At a point on the free surface of a machine component the strain rosette shown in the figure below
I need the answer as soon as possible