Data are given in the following table for completely reversed strain-controlled fatigue tests on RQC-100 steel. The elastic modulus is E= 200 GPa. Determine constants for the strain-life curve. Ga, MPa Epa Ng. cycles 0.0202 0.0100 631 574 0.01695 227 0.00705 1 030 0.0045 505 0.00193 6450 0.0030 472 0.00064 22 250 0.0023 455 (0.00010) 110000

Data are given in the following table for completely reversed strain-controlled fatigue tests on RQC-100 steel. The elastic modulus is E= 200 GPa. Determine constants for the strain-life curve. Ga, MPa Epa Ng. cycles 0.0202 0.0100 631 574 0.01695 227 0.00705 1 030 0.0045 505 0.00193 6450 0.0030 472 0.00064 22 250 0.0023 455 (0.00010) 110000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?
Given: E= 29x10^6 psi A= 2in^2 Determine the deformations members AB, BC, BE, DE and DF. Please show your complete handwritten solution.
Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam areb1 = 35 mm, d1= 115 mm, b2= 21 mm, d2 = 21 mm, and a =7 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be %3D %3D %3D %3D %3D %3D applied as shown to the beam. b2 a 不 d2 d1 b1 Answer: N-m M% =
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
650 600 550 500 450 400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016 0.018 0.02 Strain mm/mm The graph above shows the stress-strain relationship of a steel bar under tension test. The steel bar diameter = 8 mm and the bar gauge length = 100 mm. Determine the following: Toughness of the specimen Stress (MPa)
what is the modulus elasticity of 20 mm rod when a 250 MPa stress is exerted the total elastic deformation measured is 0.2mm
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are o, = 60 MPa, o, = 110 MPa, and Txy = 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components &x, y, z, and Yxy. Assume that E = 73 GPa and v=0.29 for the machine component. £x = que 11 Ox Ez = με με με μrad
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
Homework #6 Problem 1. A steel alloy core is bonded firmly to the copper tube to form the shaft shown. The materials have the shear stress-strain diagrams are shown in the figure. a) If the total applied torque is 15 kN.m, determine the torque resisted by the core and tube. b) What is the maximum elastic torque that can be applied to the shaft? What is the corresponding maximum shear strain in the shaft? c) What is the maximum torque that one can apply to the shaft? 100 m 60 mm +(MPa) 180 450 mm 15 KN-m 0.0024 (MPa) Steel Alloy 36 0.002 Copper Alloy (rad) y (rad)
Data taken from a stress-strain test for a brittle alloy are given in the table. The curve is linear between the origin and the first point. o (ksi) e (in./in.) 0 0 44.8 0.0008 54.0 0.0013 57.5 0.0017 59.5 0.0021 60.0 0.0023 Part A Determine approximately the modulus of toughness. The rupture stress is o, 30.0 ksi. Express your answer in inch-pounds per cubic inch as an integer. VAE Ivec U Submit Provide Feedback Request Answer in-lb/in³