dAB B A 50 kN 15 kN 0.6 m l -0.3 m---0.3 m-

Q: Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 14  ×   1214⁢  ×   12 -in.…

A:

Q: (a) A steel cylinder of 60 mm inner radius and 80 mm outer radius is subjected to an internal…

A: Note: As per the bartleby guidelines only three subpart will be solved at a time for remaining…

Q: In the structure shown, an 8-mm-diameter pin is used at A, and two pins are used at B and D. Knowing…

A: Given data: pin A diameter = dA = 8 mm Ultimate shearing stress  at pin A = 100 MPa = 100 n/mm2

Q: ogeth le of 25° with the horizontal. Knowing that the allowable str 0 kPa and t = 600 kPa, determine…

A:

Q: A steel pipe of 300-mm outer diameter is fabricated from an 8-mm-thick plate by welding along a…

A: Outer diameter d0= 300 mm Force P = 250 kNThickness =8 mmTorque,T=12 kN.mTo determine:a)The normal…

Q: Two cylindrical cross-section rods AB and BC, which are fixed to the wall and welded together at…

A:

Q: 8. The axle of a small truck is acted upon by the forces and couple shown. Knowing that the diameter…

A: Answer: The factor of safety at point H using Von-mises stress criteria is 1.3222.

Q: 1. Knowing that the ultimate load for cable BD (diameter is 20 mm) is 110 kN and that a factor of…

A:

Q: determine the largest load P t

A:

Q: The 2300-lb load P may be moved along the beam BD to any position between stops at E and F. Knowing…

A:

Q: Link BD consists of a single wooden member 38.2 mm wide and 20.4 mm thick. Knowing that each pin has…

A:

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: Link BC is to be made of a steel for which the ultimate normal stress is 250 MPa. Determine the…

A:

Q: (d) the average bearing stress at C in member BC, (e) the average bearing stress at B in member BC.

A:

Q: 7o solid steel shafts are connected to f a disk B. Knowing the modulus of = d the allowable shear…

A: given:shear stress τ=90MPa

Q: A 12-kN tensile load will be applied to a 50-m length of steel wire with E= 200 GPa. Determine the…

A:

Q: A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load…

A: length, L=10-in Sides of the block a=1.8 in,   b=1.6 in normal stress = 18 ksi…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

A:

Q: Link BD consists of a single bar 1 in. wide and 12 in. thick. Knowing that each pin has a 38-in.…

A: The provided system is shown below.To determine:

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.