8. The axle of a small truck is acted upon by the forces and couple shown. Knowing that the diameter of the axle is 36 mm, determine the factor of safety at point H using Von-mises stress criteria. The yield stress is equal to 200 MPa. 250 mm 200 mm 3 kN H 400 N.m 3 kN *

Q: Why is it important to determine the slopes and displacements?

A: Slope – when ever any load is applied on the beam due to its elastic properties it bend in very…

Q: What is meant by the idea of testing individual units?

A: By the idea of testing individual units we mean that it is a process of software development in…

Q: in steel, explain major axis vs minor axis explain this straight to the point

A: To explain: The major axis vs minor axis in steel.

Q: Why can overtraining be a problem?

A: Overtraining can be a problem because-  1. Sometimes body does not cope up with the pressure of…

Q: Q\Why the metals family could be strengthening

A: Both crystalline and amorphous materials may have their yield strength, ductility, and toughness…

Q: important property of many tool steals, is the ability of a tool steel to retain its mechanical and…

A: Yes, it is true.

Q: What material would work best for milling abrasive material? O High speed steel Carbide

A: Some materials that are used as abrasives include Diamond most often used in ceramic grinding and…

Q: In the 3% error, why is the design acceptable?

A: Given: There are 3% error in the design. And by this error the developed power reduced from 0.556 MW…

Q: What is impact loading?

A: Impact loading is a type of loading whose period of action is very less. Generally, when the time of…

Q: what process is this? what are the factor that need to consider?

A:

Q: Instruction: : Explain briefly the hardening pr0cess Of a metal.

A: given; explain briefly the hardening process of a metal.

Q: a) Briefly explain the advantages of hammer test over shaker test in modal testing.

A:

Q: Propose any improvements if there are any in breaking system

A: The various improvements that can be made in a breaking system are given below. 1. Increasing disc…

Q: need answer within 20 minutes please please with my best wishes

A: Superfinishing is different from honing in a way that:- In honing the small removable of material…

Q: 1. Explain how Jominy test results can be used to validate a particular steel grade for a specific…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: How does point defect affects the property of a material?

A: To find : How does point defect affects the property of a material

Q: Describe the impact loading?

A: It is a kind of loading where the load is applied for a very small amount of time. In this loading,…

Q: 2. With a neat diagram explain about honing process.

A:

Q: If the diameter with tolerance of the hole is 2.6 ±0.1 mm, which of the following is the safe…

A: Diameter with tolerance the hole =2.6 ± 0.1 mm   To find: Safe diameter and tolerance of the shaft…

Q: Generally, the Poisson's ratio of steel is

A: Poisson ratio of steel = 0.3 Option (c) is correct.

Q: How the forced vibrations can arise?

A: When a body vibrates due to the influence of external periodic force, then this type of vibrations…

Q: iii) Mention any two disadvantages of bad maintenance

A: It will decrease  lifespan of the asset .

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: With a neat sketch explain shaper machine

A:

Q: What is line of impact?

A: The line of impact is the line along which the impact forces act during the collision. Generally, it…

Q: Q1- Compare between the ferrous and non-ferrous metals in terms of the strength, hardness, weight,…

A: Ferrous metals contain iron, and non-ferrous metals don't. That means each type of ferrous and…

Q: Define deformation process

A: Deformation process is the secondary manufacturing process.

Q: Does the PLIERS have any fragile or delicate parts that need to be protected? If so, how do you…

A: Solution:   Pliers or Cutting Pliers are the mechanical tool used to cut wires, cables at the job…

Q: Describe the method of sections?

A: Method of section In this method we deal with the non-concurrent forces. Here, we get three…

Q: parameters except:   Question 8 options: a. Time b. Pressure

A: Curing process do not depends on size of the components.

Q: requirements form into different Shape, why do we need it in the design of machine elements well…

A: Machine elements are to be designed within elastic deformation regime because

Q: 8) __________ notched specimens are used for Charpy impact test. Select one: V U & V U Key hole

A: V notched specimens are used for charpy impact test

Q: 12)USM works very well when the workpiece - hardness is greater than O HRC 30

A: USM works very well when the workpiece hardness is greater than

Q: es the specification "8.8" in the standard designation of a bolt mean? Specify values including…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Name, draw a neat sketch and explain why each of the following designs of rolling mill are used…

A: rolling mill are used instead of a basic two high rolling mill.i) A mill consisting of four…