cuttingInstructions:Do not copy the drawing.Draw In third-angle orthographic projection, and to scale 1:1,the following views of the hinge:A sectional front view on A-AA top view⚫ A right view (Show all hidden detail)Show the cutting plane in the top view. Label the sectioned viewNote:All views must comply with the SABS 0111 Code of Practice forEngineering Drawing.Galaxy A05sAssessment criteria:⚫ Sectional front view0261204266[30]1110

Answered: Image /qna-images/answer/b81eeaea-7794-47a4-837b-3a26e60b411d.jpg

Answered: cutting Instructions: Do not copy the…

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter21: Reading Technical Drawings

Section: Chapter Questions

Problem 17R

See similar textbooks

Similar questions

1. Given the two views of a multiview drawing of an object, sketch the missing top view on paper. Create SolidWorks part models. Compare the top views of the SolidWorks models with your sketch. Each grid is 0.25 inch. (Do not to submit the sketch.) Submit Solidworks part models on Sac CT.
The front and the top views of a machine component are given below. Please draw 1. The front view from A-A section surface 2. The top view as given 3. The left view after you ensure the isometric view of the component on a A3 drawing paper within a horizontal direction. (It is recommended to sketch up the isometric perspective view of the component on any draft paper before drawing the multiviews.) 4. Dimension the views based on the numbers given on views. Do not try to take the dimensions from the given views. Unknown dimensions should be taken symmetric, if needed. (Make a good dimensinoning distribution of each view. Do not leave dimensionless of any view or do not repeat the same dimension in different views.) Note: Do not forget to fill a proper title block on the right comer of the paper downward. 65 20 70 125 AT TA 30 30 07 09 32 09
PART-A (Sectional View - SKETCHING) 1. Reproduce all two views given and add/complete the sectional view accordingly. 2. You may sketch the multiple objects on each A3 paper. 3. The grid square size is 5 mm. Sketch the objects with estimated size. 4. You DO NOT need to use ruler to sketch. DO NOT sketch the grid again, only the object. 5. All constructions line MUST be DELETED upon completion of the sketching.
PART-A (Sectional View - SKETCHING)1. Reproduce all two views given and add/complete the sectional view accordingly.2. You may sketch the multiple objects on each A3 paper.3. The grid square size is 5 mm. Sketch the objects with estimated size.4. You DO NOT need to use ruler to sketch. DO NOT sketch the grid again, only the object.5. All constructions line MUST be DELETED upon completion of the sketching.
I need help answering these two parts pertaining to the print provided below. For this drawing, are there other views besides View E-E and View F-F? If so, where are they? (Multiple Choice)a. No, the drawing has no additional viewsb. Yes, but they are very smallc. Yes, but they're only found on the CAD systemd. Yes, on other sheets What is the current revision status of this print? (Multiple Choice)ABCD
2 - The front and top views of an object are shown below. Freehand sketch the offset section view of the front view. Hatch the full sections view by hand. Indicate the location and the direction of the cutting plane and label the section view. Place the section view below the front view. a) The offset cutting plane should pass through the center of the slot and center of one of the holes. b) The offset cutting plane should pass through the center of the large and small holes. ........ .
Direction: refer to the image. Freehand sketch a set of front/top/right viewsby hand (in their 3rd angle canonical arrangement--front/top aligned vertically, front/right alignedhorizontally; this applies throughout remaining problems). Include all hidden lines. Usual DRAWN BY.Note: use light construction lines liberally; recall it’s OK to leave them behind provided you darkenthe part outline to differentiate it from the construction lines. Optional: build in SW to verify how eachorthogonal view is supposed to look
I need these three parts answered pertaining to the print provided below. What geometric term applies in a general way to the main objects of this assembly, whichis a primary reason only one view is required? (Multiple Choice)a. Perspectiveb. Planarc. Two Dimensionald. Cylindrical What type of section describes this one-view drawing? (Multiple Choice)a. Broken outb. Partialc. Halfd. Full During what month was this drawing released for production as revision A? (Multiple Choice)a. Januaryb. Marchc. May
I have three parts that need to be answered pertaining to the print provided below. Most of the sections on this print are full sections. What other method of sectioning is used? (Multiple Choice)A: OffsetB: HalfC: RevolvedD: Broken out On this print, there is a stem and knob assembly at an angle to the main view. If an auxiliary view were used to show the round knob as a true circle, could it be projected of off the view? (Multiple Choice)A: No, it would need to be projected from a top viewB: Yes, it should be projected from the front view Why does this drawing only have nine dimensions and those are all in parentheses? (Multiple Choice)A: It is an assembly drawing and the dimensions show distances for reference purposes onlyB: The final dimensions have not yet been determinedC: The model is parametric and the dimensions can change at any timeD: They are all 'basic' dimensions
Sketch the orthographic view as per the arrangement Note using catia v5 ( drafting ) Don't sketch the figure with pencil Thank you
LESSON: AUTODESK FUSION 360 Choose from the choices below:
I have three parts that need to be answered pertaining to the print provided below. If an auxiliary view were used to show a view looking into the hole that is inclined 15°, would the auxiliary view be projected above the left side view, above the section view, or below the section view? (Multiple Choice)A: Above the section viewB: To the left of the section viewC: To the right of the section viewD: Below the section view What is the diameter of the hole that is inclined 15°? (Multiple Choice)A: 2.5'B: 25'C: .25'D: .025' For this print, there are special triangles floating next to a few dimensions. What tolerance is applied to those dimensions? (Multiple Choice)A: .020″ (±.010″)B: .030″ (±.015″)C: .010″ (±.005″)

SEE MORE QUESTIONS

Recommended textbooks for you

Welding: Principles and Applications (MindTap Cou…

Mechanical Engineering

ISBN:

9781305494695

Author:

Larry Jeffus

Publisher:

Cengage Learning