Current Attempt in Progress Two 4-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 150 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 13,000 lb. Note that a gap of a = 0.8 in. is required between boards (1) and (2). (1) (2) Answer: L = in.

Current Attempt in Progress Two 4-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 150 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 13,000 lb. Note that a gap of a = 0.8 in. is required between boards (1) and (2). (1) (2) Answer: L = in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As shown in the figure below, a beam has a 9 - #42 reinforcement at tension and 6 - #25 reinforcement at compression.The f’c = 35 MPa, n = 8.2, and fy = 400 MPa. Determine the cracking moment (kN m) using solution 2 considering uncracked section as well as both top and bottom reinforcements. Hint; treat the top bar the same as the approach of WSD. SHOW COMPLETE SOLUTION. NEED ASAP. THANK YOU.
The nominal strength for block shear in LRFD is given by; Rn = 0.6FuAny+FuAnt < %3D 0.6FyAgy+FuAnt What does the term 0.6FyAgv represent? Buckling strength Flexural strength Shear yield strength Shear rupture strength
Give me right solution a=5 b=5
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
A channel-section has the dimensions as shown. 3) Consider a cantilevered beam subjected to an end force P. Cr (a) if cross L = 100 cm ction in is used determine its normal stress 2 2ºM 8⁰m 2cm
A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the figure. The steel bar is 69-mm-wide by 8-mm-thick. For the steel bar, the yield strength is 235 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 155 MPa. Factors of safety of 1.70 with respect to yield strength and 3.0 with respect to bearing strength are required for the bar. A factor of safety of 2.9 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Answer: Pallow= 0000 P Steel bar KN
You don't need to discuss or explain the solution; keep it simple and correct, and respond as quickly as possible.
For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
Please solve for the value of P.
Urgent. a = 10 , b = 7 solve this question about those information.
SHOW COMPLETE SOLUTION AND ILLUSTRATION
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).