COub- Explsin How mAs frow Jn9 PLume MAy BE CALCULAT ED,

Q: 4. Find the dimensions of a concrete lined open channel used to convey a discharge of 70 m/s. The…

A: Given data  Discharge  Mannings roughness coefficient  Side slope  Bed slope

Q: 20 IN H 1=3 m 3 d 1=3 m 1-3 m Which of the following most nearly gives the force in member cd due to…

A:

Q: Do, parts d, e, f, h

A: If a body  vibrates without the help of any external force it is said to undergo free vibration The…

Q: b) Determine the transformation matrix of all elements.

A:

Q: Calculate the equivalent concentrated force of distributed force diagram, draw the free body diagram…

A: Consider the free body diagram of the beam,

Q: A 40-lb aluminum bar, initially at T₁ = 150°F, is placed in a tank together with 190 lb of liquid…

A: Given data: Weight of aluminium bar=40 lb Temperature of aluminium, Ta=150°F Tank of water with…

Q: Question 1: For the truss below, using the method of joints: a) Calculate the degree of static…

A: Sorry I didn't see that you have asked for only part (b)  Ok but i have solved all the parts in…

Q: 4. A 5/8-in-diameter steel rod AB fitted to a round hole near end Cof the wooden member CD. A…

A:

Q: 3. Calculate the SDI for the following samples. Determine if the water needs to be pretreatment…

A: To calculate the SDI, we use the following formula:SDI = (1 - Ti / Tf) * 100 / Ttwhere:Ti is the…

Q: The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and…

A:

Q: PC1 PI1 0+000 Lct PT1 R1 11 STATION NORTHINGS EASTINGS 0+000 11475.55 8927.24 PC2 9291.91 9546.66…

A: To Determine Table 3 ( The Stationing of PC, PT, PC2, PCC, PT2, PC3, PRC, PT3 and End of Project)…

Q: A rigid, insulated vessel is divided into two compartments connected by a valve. Initially, one…

A:

Q: The figure as shown below is a rigid bar which is supported by two rods and a pin support. If the…

A:

Q: '. (a) Compute the runoff from a 7-in rainfall on a 1500-acre watershed that has hydrologic soil…

A:

Q: Water contained in a closed, rigid tank, initially at 100 lbf/in², 800°F, is cooled to a final state…

A:

Q: Part 8

A: Data given Load P = 250 kN Modulus of Elasticity of Steel, Es = 200 ×106 kN/m2 Modulus of…

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Finding out twist developed in steel from support B.

Q: Find the axial stress (in psi) of the steel. " Your answer Find the axial stress (in psi) of the…

A:

Q: Please do parts d, e, and f.

A: Part d, e and f is to be solved

Q: From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m. PKN L/3 m QkN/m Lm Determine the following;…

A:

Q: If F = 730 lb, F = 380 lb, F 620 lb, determine the magnitude of the resultant force acting on the…

A: Resultant force is the sum of all the forces acting horizontally and vertically.We can calculate…

Q: +y") dx ly

A:

Q: 1. Y 3" r= 3" 4" 1" 2"

A:

Q: #3 Classify each of the following trusses as statically determinate, statically indeterminate, or…

A:

Q: P2.10. Refer to Figure P2.9 for the floor plan. Calculate the tributary areas for (a) floor beam B3,…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: 4. A trapezoidal channel of bed width 8.0 m, side slopes are 1:1, longitudinal bed slope = 12 cm/Km,…

A:

Q: Air enters a compressor operating at steady state at 15 lbf/in.², 80°F and exits at 200°F. Stray…

A:

Q: Two rods vertically connect beams AB and CD as shown in the figure Point A is fixed supported while…

A:

Q: The figure below shows a simply supported beam with a vertical spring at the mid-span. The beam is…

A: Given, E=210 GPa To determine, Deflection in mm at B induced by vertical load P of 150kN acting…

Q: Stability and determinacy of structures: give the three sets of criteria of stability and…

A: Stability refers to its ability to maintain equilibrium and resist excessive deformations or…

Q: 1) Given the following: COURSE LATITUDE DEPARTURE АВ 40 - 80 BC 80 -40 CD unknown unknown DA -90 50…

A:

Q: f) Determine the axial force on each member in terms of P.

A: Find: Axial force on each member

Q: Determine the LRFD design strength (kN) of the compression member shown. The distance between the…

A:

Q: Water vapor enters a turbine operating at steady state at 1000°F, 190 lbf/in², with a volumetric…

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.