Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate fbot at the ends. (MPa), consider sign convention (- for compression, + for tension) 5 KN/m EXCLUD In6 SELFWEI6HT 300 = P P=300 KN 15M 400 de = 24 1N m3 N.A. 800 70

Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate fbot at the ends. (MPa), consider sign convention (- for compression, + for tension) 5 KN/m EXCLUD In6 SELFWEI6HT 300 = P P=300 KN 15M 400 de = 24 1N m3 N.A. 800 70

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

05) Find the minimum volume of the truss shown with constraints on the depth of the truss (y), cross-sectional areas of the bars (Al and A2), and the stresses induced in the bars (ol and o2). Treat y, Al, and A2 as design variables with oi < 105 Pa (i 1, 2), 1 msys4 m, and 0< Ai <0.2 m2 (i = 1, 2). 9 m y Bar I Bar 2 (area = Ap) (arca = A3) P = 1000 N
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring in the point.
For the figure shown below. Find the maximum allowable value of P if the bending stresses are not exceeding 3.5 KN/m² in tension and 8KN/m² in compression 0.015m 0.015m 2P |4P ЗР 0.2m . 0.25m 0.02m 2m A A 2m.
Find the m ax- shear stress for the bean below?
i need the answer quickly
Total Change in length?
Find the maximum bending compressive stress in psi, caused by the load P=1100 lbs
4. The properties of the steel-reinforced concrete beam are b =8 in., d=18 in., The total area of the steel-reinforcements is Ast = 1.25 in.?, Est/Eco= 6, and the yield stress for steel-reinforcement is (Ost) yp =60000psi. (a) Determine the bending stress that would cause the reinforcement to yield. (b) Compute the corresponding maximum stress in the concrete. h – NA d Ag (total area)
glulam beam is loaded by uniformly distributed load pch at one end by point load. The beam has a rectangular cross-section with dimensions 115\times 270 mm^2 and is braced in a rigid direction a. calculate the maximum normal stress in the beam and indicate where it goes. sketch the normal stress distribution across the door section b. calculate the maximum shear stress in the beam, indicate where it goes sketch the shear stress distribution
(ohsm 2) b. throps A simply supported beam has a rectangular cross-section of 50 mm wide and 120 mm deep. It is loaded as shown in Fig. 3b. Calculate the maximum stresses and draw the stress distribution diagram. The weight of the beam is assumed negligible. mot dit to sbutingsm s A - 2 m edband Im 10 kN B Fig. 3b 136 say xovbizon 2 m C
(c) The cross section of a quarter circular concrete block XYZof width 1.8m is shown in Figure 3. The specific weight of the concrete mix is 24 kN/m3. The hinge is along XX. Calculate the vertical force R at Y to hold the gate in this position. K Fixed slab 1.2 m Y W Fy 1.3 m FĦ D B Figure 3