Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate ftop at midspan. (MPa), consider sign convention (- for compression, + for tension)

Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate ftop at midspan. (MPa), consider sign convention (- for compression, + for tension)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve for the force in BD, vertical reaction at point C, horizontal reaction at point C, resultant of reaction at point C. What is the allowable tensile (normal) stress in member BD? What is the allowable shear stress in the pin at C? What is the required cross-section area for member BD? What is the minimum thickness t of member BD? What is the required SHEAR cross-section area at point C? What is the minimum diameter for the pin at C? (Solve for a value with the combination of mm and N)
SITUATION 3 A plate is lapped over and welded to a gusset plate as shown in the figure a. Calculate the Polar moment of Inertia of the weld group b. Determine the maximum force per unit millimeter of the weld due to the direct load c. Determine the maximum force per unit millimeter of the weld due to the moment induced by eccentrical load d. Calculate the Resultant force received by the most critical joint due to eccentric load P= 90 kN 100 mm 150 mm LO0 mm 44 kll 150 mm 150 mm
a beam is supported by a pin support at A and a roller support at B. For this question, leave your answer in terms of the variables w and L. (a) Using equilibrium of the full beam, find the support forces at A and B. (b) First section: Make an arbitrary cut between points A and B. Take the distance of the cut to be x along the beam from point A. Draw the free-body diagram for the left section and find functions for the internal shear force, V(x), and bending moment, M(x), in the section of the beam between A and B. (c) Second section: Repeat part (b) for the section of the beam between B and C. Take x to still be the distance from point A. (f) Find the value of x at which V(x) = 0. The internal bending moment reaches a maximum at the same point as V(x) = 0. Find the maximum bending mo- ment. pin Sketch the shear and bending moment diagrams. B L W C roller
A shaft/hub connection transmits a torque C =60N.m. We use a rectangular key (W=14mm x H=9mm) with a length of 30mm for a 45mm diameter shaft. Calculate the force exerted on the key.Calculate the compressive and shear stress.
A bin weighing 15 kips is supported by 3 steel tension rods. Each rod has a diameter of 1 in. Assume that the rods support equal loads. Calculate the stress in each rod (lb/in2).
QUESTION 2 A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, Su 345 MPa) for the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in KN.m? 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm 10 mm 1.805 Save A Click Save and Submit to save and submit. Click Save All Answers to save all answers. arch DELL
I-section built-in beam in the figure shows two forces It is in effect. These forces at point A and B stress element by finding the stresses that it generates Please show on. Note: force of 100 kN It is in the x-y plane and the point of action is Take as its surface. Force with a magnitude of 180 kN I is in the center of gravity of the section (Search all show transactions and required reductions
A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
Q3 The figure shows a round shaft from a gear transmission. Gears are mounted at points A, C, and E. Supporting bearings are at B and D. The forces transmitted from the gears to the shaft are shown, all acting downward. Compute the maximum stress due to bending in the shaft, accounting for stress concentrations. calculate the safety factor for the material selected.if martial 4150 OQT 1300 force 1 (f1)=9.5 kn ,Force 2(f2)=13.5Kn ,Force3 (f3)=18Kn
For the beam loaded as shown, find the maximum allowable value of P if the working stresses are 48 MPa in tension, 140 MPa in compression and 30 MPa in shear.
A 3-in. by 6-in. steel (E-29,000 ksi) bar (4-foot long) is subjected to the loads shown. Calculate the combined stresses at points A and B (be sure to indicate either tension or compression). Remember, the bar is bending in the strong direction so calculate your I accordingly. 1(1/12) (B)"(H) S=l/c A B. 6" 10,000 lbs 45,000 Ibs
Warren truss and a series of moving loads are shown in Figure 2. Assuming the loads can travel in either direction along the center of the truss. i) Draw the influence line for the force in member FC. ii) Calculate the maximum force (tension or compression) that can develop in member FC due to series of moving loads which acts along the bottom chords of the truss.