Consider the Wheatstone bridge circuit shown in Fig. 23. A Pt100 sensor which is a platinum thermometer with a resistance of 100 0 at 0°C and a temperature coefficient of 0.0039/°C is connected at the Rx(T). The sensor is capable of monitoring the temperature between 0°C to 32°C. 1k2 3k2 6V Vaut 2kO R(T) Fig. 23 i. Determine the values of R(T) at 0°C and 32°C.

Consider the Wheatstone bridge circuit shown in Fig. 23. A Pt100 sensor which is a platinum thermometer with a resistance of 100 0 at 0°C and a temperature coefficient of 0.0039/°C is connected at the Rx(T). The sensor is capable of monitoring the temperature between 0°C to 32°C. 1k2 3k2 6V Vaut 2kO R(T) Fig. 23 i. Determine the values of R(T) at 0°C and 32°C.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2) Consider the full wave rectifier circuit shown in fig 2 .The converter is operating with firing angle delay angle 45° 1. Draw and calculate the average output voltage 2. The load current in Amper 3. Determine the output power 4. Accurately plot the current through the two thyristor V1= 220 sinwt T1 100 mH V2 220 sin (wt-180) T2 2 ohm
120 Vrms 50 Hz 10Ω -E=100 V Şekil (Fig.) Find the average value of the current flowing through any thyristor when the trigger angle is 90 0 in the rectifier in the figure . Calculate the average value of the current flowing through any thyristor in the Figure above when the firing angle is equal to 90°. O 1.9445 A O 4.7463 A 0.6851 1.3549 A O 2.7098 A O 5.0347 A O 0.3415 A
Draw the circuit properly and show all steps
If the strain-gauge material is thick film resistor with a gauge-factor of 100 and an initial resistance of 500 Ohm. What is the new resistance of each strain-gauge if the strain is 0.2%. Assume a passion ratio of 0.3.
Task 1: a) Explain how you would practically test the accuracy of an electronic thermometer. b) Using TINA-TI: i) Create a circuit that will read the voltage output of a thermistor. ii) Run a DC analysis of the system monitoring the system between 0•CC and 100•CC. Displaying your results on a graph. c) Explain the advantages and disadvantages of practical testing and simulations, compare the two and explain why both are important when developing the final system.
ASSUME ARBITRARY VALUES FOR ALL OR PLUG IN VALUES U CAN USE AS AN EXAMPLE. Full Wave Rectifier: a) Find voltage at blue nodes. b) Find current at yellow arrows.
Q1) A single phase half wave rectifier shown in Fig(1) is used to charge battery E=20 and its capacity 200 wh. The primary input voltage is 120 V, 60HZ and the transformer is unity . the average charging current is 5A 1. Draw the output voltage and current wave form 2. Calculate the conducting angle of diode 3. Calculate the current limitation of resistance 4. The rectifier efficiency 5. Draw and calculate of PIV of the diode n:1 R D1 tio E
Q2/ For the half wave rectifier as shown in fig. The source voltage is 40 sinwt, find a. Vav b. Iav c. draw V, and I, · E-20Y
Q6: Determine the Thevenin equivalent at the output port of the circuit in Fig. 40 Ω ww-o Answer: -29.69 V 60 V о h₁ = 1 ks h12=-2 h21=10 h22=200 μS
I need the answer as soon as possible