Task 1: a) Explain how you would practically test the accuracy of an electronic thermometer. b) Using TINA-TI: i) Create a circuit that will read the voltage output of a thermistor. ii) Run a DC analysis of the system monitoring the system between 0•CC and 100•CC. Displaying your results on a graph. c) Explain the advantages and disadvantages of practical testing and simulations, compare the two and explain why both are important when developing the final system.

Task 1: a) Explain how you would practically test the accuracy of an electronic thermometer. b) Using TINA-TI: i) Create a circuit that will read the voltage output of a thermistor. ii) Run a DC analysis of the system monitoring the system between 0•CC and 100•CC. Displaying your results on a graph. c) Explain the advantages and disadvantages of practical testing and simulations, compare the two and explain why both are important when developing the final system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 3 a) In your own words, explain how to protect the diode from high unwanted currents, give one example to support your explanation? b) In your own words, explain why rectifiers are used and give an application from daily life using rectifiers and explain how the diode is used in this application?
i need the answer quickly
Q1. The applied input a.c. power to a half- wave rectifier is 100 watts. The d.c. output power obtained is 40 watts. (i) What is the rectification efficiency?
plz answer b and c
2a. Please I want a solution of this question with all details. Many Thanks Note: It is preferable to solve by typing.
Q1: i. Identify and write the name of rectifier giving output as in Figure B2. Output Input Figure B2 ži. Draw the circuit diagram for the above identified rectifier and explain its operation.
Subject:electronic engineering zener diode is connected reverse biased but it does bot burn why?
When comparing the efficiency of full-wave and half-wave rectifiers, one of the following statements is correct: Select one: a. Full-wave rectifier has a twice the efficiency of a hlaf-wave rectifier because it utilizes both half cycles of the input b. Full-wave rectifier has a twice the efficiency of a hlaf-wave rectifier because it makes use of a transformer c. Half-wave rectifier has half of the efficiency of a full-wave rectifier because the output frequency is double the line frequency d. Half-wave rectifier has half of the efficiency of a full-wave rectifier because it uses less number of diodes e. Half-wave rectifier has half of the efficiency of a full-wave rectifier because the ripple factor is much less
1. The full-wave controlled bridge rectifier shown has an ac input of 120 Vrms at 60 Hz and a 52 load resistor. The delay angle is 30°. Determine the average current in the load, the power absorbed by the load and the source voltamperes. V₁ I sin cor H www + Vo
Q2. This question is on laboratory work and half wave rectifiers. (a) When setting up circuits and taking measurements (Explain your connections using diagrams where necessary): (i) Why is it important to connect the various grounds together (power, oscilloscope, signal generator)?
What minimum value of series resistance is * required when three 10-watt, 10-volt, 1000- mA zener diodes are connected in series to obtain a 30-volt regulated output from a 45 volt d.c. power source? R www E₁-45 V Eo= 30 V 30 ohm O 15 ohm O 35 ohm 55ohm
Q2/ D'Arsnoval moving coil meter that modified to measure AC current with full wave rectifier, if the forward rectifier resistance is 502 , and its reverse resistance is infinity find: 1. R.. 2. The devise sensitivity for measuring DC voltage. 3. The devise sensitivity for measuring AC voltage Rs E =10 V, rm.s IT Lah2 It =1mA Rahi=400 2 Rhy 100 2 Rm = 500 2