Consider the commercial steel pipe shown in (Figure 1).Part ADetermine the flow of methane at T = 68°F in ft³/h through a 2600-ft-long horizontal 1-in.-diameter commercial steel pipe if the pressure drop is 5(10³) psi.Express your answer using three significant figures.Q = 0.744AΣ vecSubmit Previous Answers Request AnswerX Incorrect; Try Again; 7 attempts remainingProvide Feedback?ft³/h 1 in.L

Pressure Drop (ΔP) = 5 * 10^(-3) psiLength of the pipe (L) = 2600 ftDiameter of the pipe (D) = 1…

Consider the commercial steel pipe shown in (Figure 1). Determine the flow of methane at T = 68°F in ft³/h through a 2800-ft-long horizontal 1-in.-diameter commercial steel pipe if the pressure drop is 5(103) psi. Express your answer using three significant figures. [ΕΙ ΑΣΦ. | Q-0.744 4 → Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 7 attempts remaining ? ft³/h

Consider the commercial steel pipe shown in (Figure 1). Determine the flow of methane at T = 68°F in ft³/h through a 2800-ft-long horizontal 1-in.-diameter commercial steel pipe if the pressure drop is 5(103) psi. Express your answer using three significant figures. [ΕΙ ΑΣΦ. | Q-0.744 4 → Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 7 attempts remaining ? ft³/h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

12 2011KO Weeke Priv Tern Question 11 Consider the tank shown in the figure. The gate is rectangular in shape with width into the paper of 2.1 ft. Given: h = 4.0 ft B = 4.4 ft 0 = 31° Gasoline, sg=0.70 Ks- h Gasoline Ø Calculate the eccentricity (inches) of the hydrostatic force on the gate Express your answer in 2 decimal places. B hp
PLEASE ANSWER QUESTION #1 ONLY, DISREGARD THE OTHER PROBLEMS GIVEN. SHOW COMPLETE SOLUTION. THANK YOU. An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION #1: What is the mass change in the tank? note: round off to 2 decimal place QUESTION #2: What is the water level in the tank 15 min. later? note: round off to 2 decimal place QUESTION #3: What is the volume change in the tank? note: round off to 2 decimal place
Que--- A A fluid has a density of 1.11 g/cm3. Calculate its specific weight in Ib/ft3 to the nearest 10th. Your Answer: Answer A storage tank measuring 1.50 m by 2.65 m on the bottom is filled at a rate of 74 L/min. Determine the time required for the fluid to reach a depth of 24 cm. Provide answer in minutes, to the nearest 100th. Your Answer: Answer
Energy Loss in Bends and Fittings a) What is the difference between major loss and minor losses in a pipe network? Give at least three examples of minor losses? b) The following information has been collected in the lab during "Head Loss in Bends and Fittings" experiment: Manometer readings for sections before and after a bend: h₁=326 mm and h₂=253 mm Q=0.28 lit/s Pipe diameter 1.83 cm Calculate the head loss coefficient (K) for this bend. - c) Name the fitting from the lab experiment (excluding the valve) that should have the highest head loss and explain why this is the case?
Suppose that a = 3.24 m and b= 1.8 m. (Figure 1). Figure y=x¹/2 b 1 of 1 > X Part A Determine the moment of inertia for the shaded area about the axis. Express your answer to three significant figures and include the appropriate units. Submit 0 ■μÃ xª Xh Value a Provide Feedback A X-10 Units Previous Answers Request Answer W X X Incorrect; Try Again; 23 attempts remaining ? Next >
A cylindrical tank having a diameter of 40 cm in diameter and 20 cm height floats in mercury in a vertical position, its depth of immersion being 8 cm. Determine the value of MBo Unit of the Correct Answer: cm Decimal Places required in the final answer: 4
A docs.google.com/forms/d/e/1FAlpQLSetk8UE/ PROBLEM 6: A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m3 * Oil SG = 0.79 P gage = 260 kPa Gasoline SG= 0.70 Pipe Air 45 cm 50 cm 22 cm 10 cm Mercury SG= 13.6 Water Your answer
Similitude Water flows through a 5 inch diameter pipe at 10 ft/s. If a test is performed using mercury moving at 4 ft/s, what diameter pipe (in inches) would be needed to maintain the same dynamic characteristics? Both fluids are at standard temperature and pressure. Hint: What dimensionless number do we use all the time for pipes?
The containers shown in (Figure 1) are filled with water. Part A Determine the maximum pressure in the system shown. Express your answers in kilopascals using three significant figures. • View Available Hint(s) vec ? Pmax = kPa Submit Part B Determine the pressure at point B. xpress your answe in kilopascals three significant figures. • View Available Hint(s) Figure VΙ ΑΣφ vec PB = kPa Air Submit 3 m 1.5 m Provide Feedback 0.5 m
A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 40 psi, determine the gage pressure of the gasoline line. Assume the unit weight of air to be 0.0765 lb/ft3. pls answer asap thank you
The 2-kg spool S fits loosely on the inclined rod for which the coefficient of static friction is μ = 0.29. (Figure 1) Figure 0.25 m s ▸ Part A If the spool is located 0.25 m from A, determine the maximum constant speed the spool can have so that it does not slip up the rod. Express your answer to three significant figures and include the appropriate units. Value Submit Provide Feedback 4 Request Answer Units ?
About industrial piping, answer questions:Q 111: WHAT IS THE DIFFERENCE BETWEEN USING A FIXED LOAD SPRING SUPPORT AND A VARIABLE LOAD SPRING SUPPORT? Q 112: QUESTION: FOR THE CALCULATION OF SPAN BETWEEN SUPPORTS, WHAT IS THE BASIC LIMITATION TO DEFINE THE MAXIMUM DISTANCE BETWEEN SPANS? Q 113: QUESTION: HOW IS THE TREATMENT OF THE FORCES IN EQUIPMENT NOZZLES AND PIPE DERIVATIONS DONE? Q 114: QUESTION: WHAT IS THE PURPOSE OF THE FORM COEFFICIENT FOR THE CALCULATION OF FLEXIBILITY? Q 115: HOW SHOULD ECONOMIC SPEEDS BE USED?