QI:Fig. shows a pump drawing a solution (specific gravity =1.8) from a storage tank through an 8 cm steel pipe in which the flow velocity is 0.9m/s. The pump discharges through a 6 cm steel pipe to an overhead tank, the end of discharge is 12 m above the level of the solution in the feed tank. If the friction losses in the entire piping system are 5.5 m and pump efficiency is 65 per cent, determine: (i) Power rating of the pump. (ii) Pressure developed by the pump. Overhead tank 6 cm dia 15m 8 cm dia. Pump Storage tank Suction pipe Delivery pipe

QI:Fig. shows a pump drawing a solution (specific gravity =1.8) from a storage tank through an 8 cm steel pipe in which the flow velocity is 0.9m/s. The pump discharges through a 6 cm steel pipe to an overhead tank, the end of discharge is 12 m above the level of the solution in the feed tank. If the friction losses in the entire piping system are 5.5 m and pump efficiency is 65 per cent, determine: (i) Power rating of the pump. (ii) Pressure developed by the pump. Overhead tank 6 cm dia 15m 8 cm dia. Pump Storage tank Suction pipe Delivery pipe

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter = 1cm) is directed straight up. If the air gage pressure inside the tank is 200kPa, solve the theoretical volumetric flowrate out of the nozzle assuming no losses. AIR 20 m O 0.0020m^3/s O 0.0022m^3/s O 0.0031m^3/s O 0.0027m^3/s
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
Kindly answer 1,2 and 3 please
Example 2: A flow of water from a closed reservoir with interior pressure of 50 kPa to a pipe of different diameters shown in figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the .energy and hydraulic grade lines 50 kPa water 10 m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel) 2m
6. The nozzle which furnished the water to a certain hydraulic turbine 275 mm in diameter and has coefficient of velocity and discharge of 0.98 and 0.955 respectively. The nozzle is supplied from a 60 cm pipe in which the water approached the nozzle with a total head of 330 m. Compute the energy per second delivered by the jet to the turbine and the energy measure in horsepower lost in passing through the nozzle.
SUBJECT: HYDRAULICS FINALS ANSWERS MUST BE 3 DECIMALS AND BOX IT SHOW COMPLETE SOLUTION BADLY NEED IT ASAP EXPERTS. THANK YOU
Question 4: H₂=4 m f=0.15 D₁ = 50 mm H₁ 4 m 25 m L = 100 m A. Two tanks A and B were connected by a 50 mm-diameter pipe (f=0.15) that is 100 m in length. Calculate the total flow between the two tanks. B. A pipe of 200mm diameter (f-0.01) and length X is to be connected in series to replace X length of the 50mm pipe. If the purpose is to increase flow by 50%. Find Length X. ***** La=X f=0.01 D. = 200 mm
b3
Please answer, hydraulics. Thanks
Please answer and explain both questions in full detail
The pump whose characteristics are: H, = 80 – 600V²2 %3D n = -1500V² + 700V Elevation = 230 m |(2) (1) Elevation = 200 m 1000 m pipe 40 cm in diameter Pump Figure Q3 is used to pump water (µ=0.001kg/ms) a distance of 1000 m between two reservoirs the elevations of which are shown in Figure Q3 and remain constant. The pipe is 40 cm diameter commercial steel (ɛ=0.046 mm). Ignoring minor losses and assuming fully turbulent flow. Determine d) The volumetric flow rate e) The efficiency at the operating point