Consider a vertical trench of saturated undrained clay with p = 0, y = 16 kN/m3, and Cu = 15 kPa as shown in the following figure. Determine the factor of safety against rotating around point O. Assume that the failure surface (AB) is a quadrant. 0+ کے مرکز دوران 1 ۲۱ r=rºm ما را از شمال W radius: r = 3m, horizontal distance between center of mass and point O = 4r/(3ñ) ^^ A

Consider a vertical trench of saturated undrained clay with p = 0, y = 16 kN/m3, and Cu = 15 kPa as shown in the following figure. Determine the factor of safety against rotating around point O. Assume that the failure surface (AB) is a quadrant. 0+ کے مرکز دوران 1 ۲۱ r=rºm ما را از شمال W radius: r = 3m, horizontal distance between center of mass and point O = 4r/(3ñ) ^^ A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Ta Hypothetical Case: Slope Soils Natural or man-made slope Potential failure plane 01 35° |0₁-652 0₁ = 52 kPa a = 35° 03= 12 kPa Horizontal Slope failure (landslide) will be triggered at any point along the potential failure plane when the shear stress exceeds the shear strength of the soil mobilized in the opposite direction.
A cut is made into a homogeneous soil as depicted in the figure below, at an angle of 60° with the horizontal. Calculate the resisting shear force in kN along the failure plane given that the shear force applied by the overlying soil wedge is 120 kN. The failure plane is at an angle of 40° from the horizontal direction and the ground water level is below this plane. Assume drained conditions for this question.
Q5 a) The discontinuity characteristic mostly dominates failure in the rock mass. Thus, the selection of stabilisation must be made based on the mode of instability. Answer the following question: a) Figure Q5(a) shows two types of failure modes in rock; rockfall and wedge failure. State the rock mass characteristic that contributes to these failures and propose a suitable stabilisation measure for both cases? UTM ITIVA M M &UTM&UTM (ii) B) It is a common practice to install shotcrete and wire mesh together. For an unstable slope face, why such practice is highly recommended. What is the purpose of wire mesh in shotcrete installation?
A conical friction clutch with cast iron contact surface transmits 130 h.p. at 1500 r.p.m. The cone angle is 20° and the coefficient of friction 0.20. If the mean diameter of the bearing surface is 37.5 cm and the intensity of normal pressure is not to exceed 30 N/cm², find the breadth of the conical surface.
(1b) Estimate the settlement of a 10 m square area loaded 1 m at 100 kN/ m3 placed 1 m below ground level with ground water at the level of the footing. The static cone resistance values for the sand deposit are as follows: G.L to 6 m = 8000kN/m3,6 -11 mm = 10,000kN/, below 11 m =12,000kN/m3.
A 10 m high sope of dry clay sol (unil weight = 20 N/m) with a slope angle of 45 and the circular slip suriace, is shown in the figure (not drawn to the scale). The weight of the slp wedge is denoted by W. The undrained unt cohosion (C) is 60 kPa. 10m Unit weight= 20 kN m C = 60 kPa 10m 448m, 45% The facter of safety of the slooe against sip failure. IS
Using the FE handbook, can I get a step by step on how to answer?
An excavation in soft clay is supported by a braced sheet pile wall. Calculate the force in strut A. O a. 631.92 kN O b. 151.67 kN O c. 203.53 kN O d. 430.87 kN Struts are spaced 2.5 m centre to centre Soft clay %=17kN/m³ S20 kPa $=0° max=yH = YH (1-4) H Q|25H
Determine the induced vertical stress at a depth of 1.0 m below on wheel due to a heavily loaded wheel assemble below: Each wheel has a load of 195 kN. What stress value will you consider for the design of runway? Y 1.12 m (center to center) 1 1.47 m (center to center)
please solve the question given in image.
For the trial slip circle shown in figure, calculate the factor of safety. [(Given: weight of the soil = 346 kN/m, unit weight of soil = 19 kN/m3, C = 20 kN/m2] %3D r=9 m 70° 5 m 7XXX
1. Find the maximum axial forces for the members U4US, LLs, and L4Us due to the given loading U U2 U4 Us 6 k 3 k | 2 k4k 10 ft Lo L L1 L2 L3 L4 Ls 6 at 15 ft 90 ft 5 ft 3 ft 3 ft