An anchored bulkhed 5.1 anchor rods 1 m below the top and depth of embedment is 1.5 m. Determine the factor of safety against failure. Angle of internal friction of sand is 30° and the sand is wet throughout having a unit weight of 16 kN/m³. Comment if the depth of embedment is adequate. If not, obtain the depth of embedment using a factor of safety of 2. A D = 1.5 m TI/W P₁ B C 0.5 D 1 m P. T 1.7 m 5.1 m

An anchored bulkhed 5.1 anchor rods 1 m below the top and depth of embedment is 1.5 m. Determine the factor of safety against failure. Angle of internal friction of sand is 30° and the sand is wet throughout having a unit weight of 16 kN/m³. Comment if the depth of embedment is adequate. If not, obtain the depth of embedment using a factor of safety of 2. A D = 1.5 m TI/W P₁ B C 0.5 D 1 m P. T 1.7 m 5.1 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve for and give a good explantion and step by step solution
Ex Find Disc hange and mea shear stress in channel show has slop 1:2000 and 3.0
A deposit of sand exhibited the following properties: Angle of internal friction, = 35° Dry unit weight, yd = 17 kN/m³ Saturated unit weight, Ysat = 20.7 kN/m³ will Man 59 2 = F 20- 18.4 What is the shearing strength of the sand along a horizontal plane at a depth of 4 m given that the water table is at a depth of 2.5 m from ground surface? Find the shear strength when the water table rises to the ground surface.
For Questions A and B a temporary earth support wall is supporting a 25 ft excavation. A. Neatly draw the active soil pressure diagram, based on Rankine Theory, behind the wall and show the maximum pressure at the bottom of the temporary wall after completion of the excavation. Also indicate the location of the theoretical slip (failure) plane and its angle from the vertical. The soil is a saturated clay with properties as follows: gsat = 132 pcf, f = 19o c = 450 psf B. Use table 5.5 in the textbook and repeat problem 2 for a medium-dense gravely-sand with the following properties shown on the table: gin-situ = 120 pcf, f = 34o c = 0 psf
Determine the stress in member dg. A 13.33 KN (T) B) 21.33 KN (C) 14.17 KN (T) D 52.00 KN (C) None of the above 8 kN b 16 kN h 20 kN 4 @ 20 m 80 m- 16 KN 15 m 7.5 m ...
Q-A hollow rectangular masonry pier 600 mm x 900 mm and 150 mm thick transmits a vertical load of 500 KN in a vertical plane bisecting the 900 mm side and at an eccentricity of 100 mm from the geometrical axes of the section. Determine the maximum and minimum stress intensity in the section.
Soil mechanics Geotechnical Engineer. Please solve in clear writing With sincere thanks and appreciation
Kindly answer with complete solution please. Needed ASAP
Q/Along flexible strip Looting of 2.5m width having a smooth buse, is subjected to aurilor distributed load of 80 kN/m². Determine the vertical stress intensitres al adepth of 2m below: i) center line of the looting 2:5m (1) at side face of the looting 2m ii) at a point 1-5m, from the side lace t T₂ = = [2 + Sin α cos (d+ 2B)] 옺[a 94
Determine the induced vertical stress at a depth of 1.0 m below on wheel due to a heavily loaded wheel assemble below: Each wheel has a load of 195 kN. What stress value will you consider for the design of runway? Y 1.12 m (center to center) 1 1.47 m (center to center)
Note:hand written solution should be avoided.
4- A moderately curved channel with a slightly rounded non-cohesive bed material with a diameter of d50 = 25 mm carrying a discharge of 30 m³/s. The longitudinal slope of the channel is 0.001 and the side wall slopes are designed to be 60% of the angle of repose of the bed material Note: Use the Strikler's formula to calculate Manning's value. Use the Swammy and Mittal's formula to estimate the critical shear stress. Use the free board depth of 0.5m. a) Design the channel using the tractive force method for a Boly ratio of 20 b) Design the channel using the most efficient hydraulic section c) Discuss about the channel stability and erosion for both designs in parts a and b Strickler (Chow, 1959) proposed a correlation between the mean diameter of bed material, dso, and the Manning's coefficient as: n = 0.039d¹/6 Swamee and Mittal (1976) proposed an explicit equation to express the Sheild's curve defined as: 50 0.409d² 1/2 (1+0.177d² )¹/¹² T = 0.155+.