Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above. (Assume necessary data) a. The output voltage is 12 V, the output power is 540W b. The output voltage is 12 V, the output power is 54W c. The output voltage is 12 V, the output power is 5.4W d. The output voltage is 24 V, the output power is 2.25W

Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above. (Assume necessary data) a. The output voltage is 12 V, the output power is 540W b. The output voltage is 12 V, the output power is 54W c. The output voltage is 12 V, the output power is 5.4W d. The output voltage is 24 V, the output power is 2.25W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Quèstion 5 The majority of charge carriers in P-type semiconductors are electrons. O True False A Moving to another question will save this response. Chp
it's urgent please solve asap
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to り:1 L-Dc こ0SA ドL VL-De =20V 220V omsh 0.01 F 0.02 F O 0.0167 F None of the above A Moving to another question will save this response. « F8 F10 %$4 48 & 50 67 7V 8人 99 1O 3. F GJ H. K. Corll %24
use the kvl and draw its schematic diagram
Question 15 In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True False Moving to another question will save this response. ip
QUESTION 1 If a multiratio CT having 150:5 CT ratio with 0.104 ohm secondary resistance and the excitation current 0.2 A, I -SA Za1 ohm. a) Find the primary side of the CT and show the details of your work. b) Find the CT error and show the details of your work.
b) Figure 3 shows the AC voltmeter that is given to you to make a measurement of 240Vrms from TNB AC supply. However, the voltage range is lower than the voltage of TNB AC supply. By using given AC voltmeter, design the new AC voltmeter circuit to measure the required voltage. Given Sac AC voltmeter meter is 5k2/V. Assume that the meter indicator will deflect 50% of full scale during measurement. V 40 30 20 10 CE 2-151 Figure 3
Q6 Choose correct answer
The source voltage of the circuit is 5V and the break down voltage for the Zener diode is 5.2V then the voltage across resistor will be ??
1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. Ans. r= 1.6 ohm 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. Ans. 2.667 V and 3.333 ohm 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the Internal resistance of the battery. Ans. 18.75 V and 0.75 ohm 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be…
Could some please provide an explanation for VL why 15 and 1.33
A circuit consist of a single diode and resistor which are connected to AC source. The resistance voltage is: O AC voltage with V=Vm/ O DC voltage with V=Vm/√2 O AC voltage + DC offset O only DC voltage with V=2Vm/