Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A 220V oms! VL-DC =20V 01 F 02 F 0167 F

Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A 220V oms! VL-DC =20V 01 F 02 F 0167 F

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
For the circuit shown below, sketch to scale the output V waveform and draw the transfer characteristic (V versus Vi), Assume the diodes are ideal.
Draw the circuit diagram of a simple negative clamper with input and output waveforms (with values) for an input peak to peak of Vpp = 12 Volts .Assume Germanium diode is used. Solve it quic plz
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KO. Then explain briefly the effect of changing in the RL value on the output waveform. 5:1 Vp= 0.7v for all diodes Vma 100 V f= 60H2 D S0uF
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
Calculate the diode current, lo, for the circuit shown. The source has Va 1.5 V and R = 0.8 92 and each of the diodes has Is = 10" A. // 21-15001 = 1.5 Vth R+h0.8 22 ↓ID ve
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Consider diode circuit shown below with Vcc=5V and V₂ = 3V. U₁A HH +V₂ ū The peak inverse voltage on the diode is close to V₁ V. A Vo
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…