Compute the total discharge in the stream based on thẻ given cross section information.distance, m612182430depth, m1.61.92.51.30.6velocity, m/sJat 0.2 depth1.72.3 ·2.41.80.7-..at 0.8 depth1.11.921.20.3...

Assuming same the cross-sectional dimensional through: The average Velocity will be,…

Answered: Compute the total discharge in the…

Compute the total discharge in the stream based on thẻ given cro 12 18 24 30 distance, m 1.6 1.9 2.5 1.3 0.6 depth, m velocity, m/s at 0.2 depth 1.7 2.3 2.4 1.8 0.7 at 0.8 depth 1.1 1.9 2 1.2 0.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A concrete-lined trapezoidal canal is 20 ft. wide at the bottom with sides sloped 3 horizontal to 4…

A: Base width = 20 ft,Sides sloped = 3 horizontal to 4 vertical,Slope of the bottom = 0.0025,Depth of…

Q: A small orifice in area is in the vertical side of a rectangular tank. The horizontal sectional area…

Q: 6- Estimate the TOTAL streamflow in the channel below given the values in the table and the flow of…

Q: 4. Determine the total discharge from the stream data provided. Velocity (m/s) Point Depth (m) 0.2d…

A: the diagram of given streams in which specific point is provided

Q: Table 1 shows the data for the network of pipes connecting four reservoirs to a common junction, J.…

Q: Water Resources Engineering: Given the stream section and the following measurements, calculate the…

A: The discharge is given by

Q: While measuring the discharge in a small stream, it was found that the depth of flow increases at…

Q: Q (5-2)/ Water flows uniformly in an earth rectangular cross section open channel. Data available…

Q: The following twenty problems refer to a transition in a rectangular channel with a bottom elevation…

Q: Compute the discharge rate (cfs) of a uniform flow in a 6 ft diameter brick pipe. The pipe is…

A: Diameter of pipe = d = 6ft. Depth of flow = y = 4ft. Slope = S = 20% Manning's coefficient for…

Q: A Parshall flume is to be designed to measure the discharge in a channel. If the design flowrate is…

Q: The top width and the depth of flow in a triangular channel were measured as 4 m and 1 m,…

A: A triangular channel- Top width=4 m, Depth of flow =1 m, Velocity at surface- V=0.7 m/s, Velocity at…

Q: Question The values given in the table below were obtained from a flow observation station.…

A: Find The total flow.

Q: 4. Determine the total discharge from the stream data provided. Velocity (m/s) Point Depth (m) 0.2d…

A: Given data: Assuming width between the points as 1m.

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Compute the total discharge in the stream based on thẻ given cross section information.
distance, m
6
12
18
24
30
depth, m
1.6
1.9
2.5
1.3
0.6
velocity, m/s
Jat 0.2 depth
1.7
2.3 ·
2.4
1.8
0.7
-..
at 0.8 depth
1.1
1.9
2
1.2
0.3
...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1:Assuming same the cross-section :

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

3) Find the normal depth of flow for a discharge of 50 cfs in a 48 inch diameter concrete pipe (n = 0.012). The pipe has a slope of 1.90 percent. Use the Charts.
Find the depth and the top width of a V-notch capable of discharging a maximum of 0.7 m3/s such that the head shall be 75 mm for a discharge of 5.6 liters per second. Its Cd is the same as that of a similar right angled V-notch for which the flow is given by Q = 1.407H5/2.
4. A. Find the discharge in stream flow for the following data B. Find manning coefficient at slop 0.01% and flow 15m³/s (20 marks) Distance from bank(m) 1.5 Depth of water (m) 1.3 2.5 Velocity at depth 0.2(m/s) 0.6 0.9 Velocity at depth 0.8(m/s) 0.4 0.6 3596 4100 5775 4.5 9 7.5 1.7 1.0 0.4 0.7 0.6 0.4 0.5 0.4 0.3 9000
Problem 7-61
Q1) The following data were collected during a discharge measurement operation. Compute river discharge. Width of each sub- section is (1.5)m Depth (m) V(0.2d) m/sec V(0.8d) m/sec 1.3 0.6 0.4 2.5 0.9 0.6 1.7 0.7 0.5 1.0 0.6 0.4 0.4 0.4 0.3
1. Three reservoir A, B, and C are connected by pipelines 1, 2, 3 respectively which merges at a junction X. the elevation of reservoir A is 300 m and that of B is 285 m. The rate of flow from reservoir A is 1.4m³/s A) Compute the rate of flow in reservoir B B) Compute the rate of flow in reservoir C C) Compute the elevation of reservoir C EL 300 m Qb = 0.189 m³/s (receiver) Qc =1.211 m/s ELC = 148.93 m EL 285 m. VEL? Pipe 1 2 3 f 0.0157 0.0162 0.0177 diameter (mm) 800 600 450 Length (m ) 1500 450 1200
Triangular notch with vertical angle of 90° measures a flow rate. If the value of Cd = 0.6 and there was an error of 2.5 mm in the measurement the head, then calculate the percentage error in estimation of discharge of 21 lit/s.
m10
In a rectangular open channel, 2.0 m wide, water flows at a depth of 0.8 m. It discharges over an aerated sharp crested weir over the full width, with depth over weir crest being 0.25 m/ Cc = 0.61. Adjusting for velocity head of approach, what would be the discharge through the channel? √29= 4.43 units.
What is the discharge through a 1.5-m wide box culvert of square cross-section with slightly rounded entrance and headwater of 1.9 m? Select an answer and submit. For keyboard navigation, use the up/down arrow keys to select an answer. a 4.5 m³/s с d 5.8 m³/s 6.0 m³/s 7.2 m³/s
6.8.11. A diversion gate backs up flow in a 5-ft wide rectangular irrigation channel (So = 0.001, 0.015). The discharge in the channel is 50 cfs. If the depth of flow at the gate is 5 ft, deter- mine the channel and flow classification (e.g., M-2, S-1) upstream of the gate and explain your supporting logic. Then determine the water surface profile by finding the depth of flow at distances of 200 ft, 500 ft, and 1,000 ft upstream of the gate. Use a spreadsheet or appropriate computer software to perform the computations. (See the book's preface for computer software suggestions.) %3D n%3D