Determine the flowrate for the symmetrical channel shown in the figure below if the bottom is smooth concrete and the sides are weedy. The bottom slope is So = 0.001. ő 5ft 3ft ↓ 15ft ft³/s

Q: A simply supported steel beam EVEN: 12m long carries a uniformly distributed load of 22KN/m load…

A:

Q: On the drawing (attached , apply a datum feature symbols to create a datum axis A-B by using the…

A: The given data is: For left side: Shaft Diameter Upper Limit=9 6.40 mmShaft Diameter Lower Limit=ϕ…

Q: R20

A:

Q: e section are given by the table. The beam is subjected to the concentrate the couple moment Mo…

A:

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: permanent load Î Required Ума, + багаг <R Q₁ JA Q (0.3) variable load recall ₁8/₁0 = 12₁ √x. - OR ge…

A: Reference : Foundation design, Shallow depth design. Given  : A set of cubic equation To determine :…

Q: dv dx dydz + 8x dy dxdz y v dydz + v dxdz y dx dz dy Vy

A:

Q: Given the two orthogonal projections of the object (top view and front view), identify the third…

A: Data given Find the side view

Q: Determine Ix and Tx.

A: GIVEN- A PLANE FIGURE TO FIND- MOMENT OF INERTIA ABOUT X-AXIS AND CENTROIDAL AXIS.

Q: Determine: a) Differential Area b)  Centroid distance along x and y axis   *use 3 decimal places…

A:

Q: Find the range of: f(x)=Vx+4.

A:

Q: To draw the shape below you need to use from the draw panel - - --- - 35.6 740° 80.0 120 120 80,0…

A: Given data- An irregular shape is given as shown below- To find- The number of commands required to…

Q: free-body diagram. Yo

A:

Q: 200 N 53° A 36° 1.5 189 N 42 kN/m 3 В 4 3

A: When we are calculating the moment due to udl or Uvl we calculate it as  Force acting /m length ×…

Q: at state of given (All in The Stres point is MPa) 80 100 100 i) And Principal Stren & Principal…

A:

Q: 4. From the figure shown, Determine, e. Centroid with respect to x-axis f. Centroid with respect to…

A: Find centroid with respect to X and Y axis  Find moment of inertia with respect to centroid of X and…

Q: a) Find ū and I Tolm 0,1m %3D 0.3m 0.am' 0Am 0.m

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: determine the reading at "D"

A: A levelling staff is given, we need to find out the reading at D

Q: 1. What is the value of ybar from the 1-1 line [ Select ] 2. What is the value of centroidal MOI…

A:

Q: 3. A 12m beam simply supported at 1.3m from both ends carries a uniformly distributed load of 18KN/m…

A:

Q: locate the centroid area of the plate, all the unit is in mm.

A: Labelled diagram of the different section -

Q: What is the type of traverse shown in the picture? (select all that apply) Az Mk (a)

A: Given that:

Q: Q6) Define the following words. 1-Optical Square 2-Bench Mark (B.M)

A: Surveying:-  The survey is a science or art to locate an unknown point with respect to a known…

Q: Identify and circle others Simply Supported Beam and continous Beam at structural drawing

A: To Identify Simply Supported Beam and continuous Beam at structural drawing, other than that which…

Q: A 500 N 2m 120⁰ 3 m 200 N

A:

Q: a) H 20 mm 80 mm Calculate Iz 20 mm 60 mm 20 mm b) Calculate maximum Q and indicate the location on…

A: Given: A I cross section Required: Moment of inertia about Z axis Maximum value of Q

Q: Compute Ix (I sub x, in mm*, round-off to 2 decimal places) for the region shown. 60 mm 80 mm 20 mm…

A:

Q: Let F₁ = [F1] N. i) Express F₁ as a Cartesian vector. F₁ X 3 5 4 30° 45° F₂= = 450 N - y

A: To represent F1 as a Cartesian vector. F1 = 647 N

Q: D A E Given side B G Assuming that all stations are occupied and al lines are observed, what is the…

A:

Q: Given: |Change in length of BE=0.00352a mm Area(BE)=150a mm? E Area(CF)=150a mm? E=200 GPa Required:…

A: To find the change in length of CF-

Q: Determine the coordinates of the centroid of the lines shown with respect to the indicated X and Y…

A: Given, A section,

Q: Calculate uniform load W that the cantilever beam can carry having a length of 3m. The section of…

A: Given: Span. L = 3 m fc = 25 MPa fy = 276 MPa Tension reinforcements, 5-#28 mm h = 650 mm hollow…

Q: 5 10 35 30 11E 25 10 15 20 25 .001 in. 10

A: 3 English Fixed scale reading = 0.8inch 4 English Vernier scale = 16 Least count = 0.001 inch Net…

Q: The reduced form of 3y (0) – 21y (4) + 5y''– 10y"+42y'- 8y+ 5=0 js: A (3D5- 21D4+5D³ – 10D²+42D – 8)…

A:

Q: 100 A 9, A3 200 1. What is the value af ybar from the 1-1 line (Select) 2. What is the value of…

A:

Q: 10" 3.1 k-2" 15" Sx = ? (2) Zx = ? (1)

A: Given: To find: Elastic modulus, Sx Plastic modulus, Zx

Q: Figure, 50mm 50mm 50mm 50mm 250mm N.A C.g 100mm 93 100mm 100mm

A:

Q: Which feature control frame would you use to tolerance the one-inch slot perpendicular to datum…

A:

Q: la 5 in. 8 in. -s in.8 in.-

A: To Find :- centroid