3.Compute the equivalent von Mises' stress, deq, for the following plane stress state.%₁ = -40 ksi, 0₂ = -12 ksi, T12 = 5 ksiVon Mises' yield criterion is expressed by the following inequality1√ [(0p₁ - Op2₂)² + (Op2 − Op3)² + (Op3 − Op1)²] ≤ Oy,Jeq =

Given data:- σ1= -40 ksiσ2 = - 12 ksiτ12= 5 ksi To find:-the equivalent von- Mises' stress

Compute the equivalent von Mises' stress, deg, for the following plane stress state. %₁ = -40 ksi, %₂ = -12 ksi, T12 = 5 ksi Von Mises' yield criterion is expressed by the following inequality √/2 √1(0₂₁ - 0₂²)² + (0₂² · √ [(op₁ - 0p2)² + Jeq = (Op2 − ¯p3)² + (σp3 − Op¹)²] ≤ Oy,

Compute the equivalent von Mises' stress, deg, for the following plane stress state. %₁ = -40 ksi, %₂ = -12 ksi, T12 = 5 ksi Von Mises' yield criterion is expressed by the following inequality √/2 √1(0₂₁ - 0₂²)² + (0₂² · √ [(op₁ - 0p2)² + Jeq = (Op2 − ¯p3)² + (σp3 − Op¹)²] ≤ Oy,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P = 50 kN. The elongation of the rod is 8 = 1.40 mm, and its diameter becomes d2 = 19.9837 mm. Assume that the material does not yield. Determine the following: P = 50 kN 600 mm 20 mm P = 50 kN The normal stress is equal to in MPa: The normal Strain is equal to: The modulus of elasticity is equal to in GPa: The changes in diameter (Ad) is equal to in mm: The passion ratio is equal to: The shear modulus is equal to in GPa:
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.8 mm and upward by v = 5.4 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 635 mm, a = 26°, and 3 = 64° U Answer: y = P R urad
Q1: The stresses measured at a point on bone are oy =5 MPa ,o, = -7 MPa and 1,,=2.4 MPa find: 1. The principal strains and maximum shear strain. 2. The strain energy . Knowing that the poisonratio v=0.3 and the unit volume change =5.6x10
A 50-mm diameter cylinder is made of a brass for which the stress-strain diagram is as shown. The angle of twist is 5° in a length L = 845 mm. The three points on the nonlinear stress-strain diagram used are (0, 0), (0.0015, 55 MPa), and (0.003, 80 MPa). By fitting the polynomial T = A + By+ Cy2 through these points, the following approximate relation has been obtained. T= 46.7 x 10y-6.67 × 10122 Determine the magnitude T of torque applied to the shaft using this relation and the two equations given below. P4 Y = Ty = 2π] ρ?τὰρ 7 (MPa) 100 80 60 40 20 0 0,001 0.002 0.003 Y d = 50 mm "K The magnitude T of torque applied to the shaft is KN-m. A²
4.1: Unit elongation in three directions at a point a,Since Ꜫa = 120.10-6 Ꜫb = -320.10-6 Ꜫc = 650.10-6, find the unit elongation in the I - I direction. Draw the mohr circle of the Strain state. Answer = Ꜫ45◦ = -850.10-6
Determine the allowable stress in last example if the factor of safety is 2.5.
Compute the equivalent von Mises' stress, deq. for the following plane stress state. %₁ = -40 ksi, 0₂=-12 ksi, T12 = 5 ksi
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.4 mm and upward by v = 5.1 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 680 mm, a = 21%, and ß = 69% If U Answer: y = i P a B R urad
Suppose that σ = 330 psi and Try = 150 psi in (Figure 1). Figure Part D Specify the orientation of the principal stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. Op₁= Part E OF 0₂ = ΑΣΦΙΚΗ vec Specify the orientation of the maximum in-plane shear stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. 0/ —| ΑΣΦ 11 | vec ? ? o
How can I draw in mohr's circle?
A large thin rectangular plate is subjected to certain traction boundary conditions on its thin edges. The following stress function is proposed for this problem: 2 p(x,y) = A x¹ + B x²y² + Cy² (i) use the biharmonic equation to find restrictions, if any, on values of A, B, and C (ii) calculate all stress components (iii) calculate all strain components in terms of A, B, and C as well as the Young modulus and Poisson's ratio E and y, respectively. (iv) check that the equilibrium equations are satisfied (v) determine the traction boundary conditions at x=+a and y=+b
The 16 x 22 x 25 mm rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 651N causes the upper frame to be deflected downward by 8.3mm. Determine the average shear (in prad) strain in the rubber blocks. Note: Do NOT include units in your answer Double U anti-vibration shear mount Rubber block dimensions Shear deformation of blocks Answer: