cm If the diameter and thickness of a hollow shaft are 12.5 cm and 10 mm. Then its polar moment of inertia value is Select one: O a. 1203.52 O b. 2396.74 O c. 1415.09 O d. 679.762

Q: 25. ..s) Two circles, each of radius r, have their centers located at (0,2) and (0,3). Each is used…

A: As per honor code and answering guidelines I can  answer 1st question at a time.If you want other…

Q: A 3/4-in.-diameter hole is drilled in a piece of 1-in.-thick steel; the hole is then countersunk as…

A: The required volume of the given hole is obtained by rotating the area shown about the Y-axis.

Q: Find the value of a. TO a. Vs +3

A:

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: Nut 17.0 N 37° 25.0 cm

A: The text provides the following information:The force applied to the wrench is 17.0 NThe distance…

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: Find Rotate the object about the given axis.

Q: find the center of the given shape

A:

Q: 3.00- 1.25-

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: Draw the front, Side and top

A: We need to draw three orthographic projection views.

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: the solution is provided in the picture attached below.

Q: A pump is being supplied with water from an open tank. The water level of the sOurce

A:

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: In an experiment, an engineer wants to compare the torsional capacity of two shafts of the same…

A: Given data is

Q: 1. Determine the cylinder displacement and engine displacement of an engine having six cylinders…

A: given data  bore diameter = 102 mm = 0.102m stroke length  = 120mm =0.120m number of cylinders =6…

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: Q3: Draw the geometry shown in figure below . 88 38 12 719 -28 12 50

A:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A: According to the question data MA=200lb.inclockwise   and the figure  We need to find Force F to…

Q: What is the direction of the edge formed between the intersection of (211) and (102)?

A:

Q: Find the center of gravity of the wire.

A: The centroid, when referring to a solid item, denotes the geometric center or the location where the…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d )  of steel bar is given, area of the circle is in terms of…

Q: The power and motion can be transmitted from one shaft to another shaft by means of gear drives

A: According to given details provided in the question

Q: 11 The volume of a cube with sides of L is L. If the length is measured as 121 +2 mm, determine the…

A: Given data  The length measurement = 121+/-2 Find the worst possible error in the volume

Q: For machine element, locate the centeroid

A: Answer:  Centroid ( 44.78 , 27.19 , 26.25 ) For a step-by-step solution have a look through the…

Q: If this were to be written how would it look like?

A: Geometric Symbol – This symbol is most useful and shows the position of the dimensions. Diameter…

Q: Solve for the tensions 45 50 g

A: Given: W=50 g Consider the Free Body Diagram:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A: