Answer it with correct/exact and clean Solution to get the rate A pump is being supplied withwater from an open tank. Thewater level of the sourcereservoir is óm below thepump center line. The lengthof the pipe (suction line ) is10m and 50cm innerdiameter with (coefficient offriction of .025). Theatmospheric pressure of thataltitude is 101325 Pa, andpump flowrate is 300 L/s. IFthe vapor pressure of 20 °Cwater is at 2400 Pa, what isthe NPSHA of the pump inmeter?Upload the complete solution of theabove problem.

Answered: Image /qna-images/answer/408f903c-41c5-4579-804f-0e9b400e90e0.jpg

Answered: A pump is being supplied with water…

Engineering

Mechanical Engineering

A pump is being supplied with water from an open tank. The water level of the sOurce

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Venturimeter of 30 crn x t 5 cm is fiued inhorizontal pipe line of 15 cm diameter to measure flow rate. The level difference ofbcth limbso1' rnercury differential manometer connected tothe venttrlmeter is 15 cm. Calsulate the flowrateofwater through the pipe" Take Coefficientof velocity as 0.96. derive the formula use
A pump discharges 8000 liters per minute of a certain brine solution (SG=1.20) to an evaporating pond. The intake line is 25cm in diameter and is at the same level as the pump discharge line, which is 15cm in diameter. The pressure at the inlet of the pump is -170mm of mercury. The pressure gage connected to the pipe discharge reads 150 kPa, and its center is 2.0mabove the center of the discharge flange. The vapor pressure of the brine solution is 40mm of Hg. If the pump efficiency is 80%. How much power is required?
In some high-rise buildings, water is stored in an elevatedtank on the roof to minimize pressure fluctuations inthe system. Consider water that is pumped through a 10-cmsteel pipe to the roof of a 200-m-tall building; the pump ison the ground floor. For a water temperature of lOOC and aflow of 0.02 m3/s, what is the pressure at the pump discharge(in kPa)?
ther f Q3
7:23 M When the level in the tark is 10 m above the centerlire of the outlet, how fst is the level in the tank falling? WouH 10 m (3) Weaeofferedsomepipes madeof arnew kindof plastic. Totest their roughress, we pump water throgha 0.0762 m pipe made of this material atanaverage velocity of 12.19 m/s The dbserved Faning friction factor is 0.0032. Estimate the absolute rougnessof this pdastic. (4) What pressure drop is required in order to pump water at 20°C through a pipe 25 am in diameter and lengh 1234 m at arte of 1.97 m2 sec? The pipe is harizrtal and contains four stadrdradius 90° elbows and two 45° elbows. (A standard-radius 90° elbow isroughly equivalert to the resistance offered by apipeof length 32 diameters a 45° elbow, 15 diameters) (5) Cansider the steedy-state flow of animompressible Newtonian fluid througha hrizartal tube f irner radius Radlength L, sshown belpw: Findthe velocity distribution in the liquid Neglect end effects. Page|2 End I Recommended Share Extract Pages…
Consider water fl owing by gravity through a short pipeconnecting two reservoirs whose surface levels differ by anamount D z . Why does the incompressible frictionless Bernoulliequation lead to an absurdity when the fl ow ratethrough the pipe is computed? Does the paradox havesomething to do with the length of the short pipe? Does theparadox disappear if we round the entrance and exit edgesof the pipe?
I need correct ans with step by step method
Brine is flowing through a coil with a velocity of 240 fpm, The pressure foss in overcoming me traction in the coil 3.134 psia. The diameter of the coil is 3 ft and it has internal diameter of 1.20 inches At 86 degree Fahrenheit, the density of the brine is 995.6262 kg/m and its viscosity is 0.10081067 PA. a.) Calculate for the fanning friction factor in problem. b.) Determine the number of turns of the coil.
A pipe of diameter 14 cm, is used to pump the water to the house in the Hamra hill at the height of 80 m than the ground. The discharge at the end of the pipe is 140 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 34 N/cm. Find the following: O The velocity head at the entry of pipe (in m) (m Pressure head at the inlet (in m) (m) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id.) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe (unit in m)
A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill at the height of 60 m above the ground. The flowrate at the end of the pipe is 180 lit/s. The pressure gauge is connected at the inlet of the pipe in the ground and measured as 35.5 N/cm2. Find the following: (i) The kinetic energy per unit weight at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe entry (unit in m)
the maximum value of h ?
We have a tank (large enough to neglect the velocity of the fluid surface in the tank v1 =0). The tank contains water at a mevel of 15 meters. The tank is enclosed and the air space above the water is at 5 atm. The exit of the tank consists of 25 meters of 2 cm diamter pipe with d/D = 0.0004. It exhaust to the atmospere at 1 atm. What is the exit velocity?