The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.“]. For the loading shown,determine:(a) the beam deflection at point A.(b) the beam deflection at point B.Assume MA = 180 kip-ft, P = 12 kips, LAB = 3.8 ft, LBC = 5.7 ft.MAABLABLBCAnswer:(a) VA =in.(b) VB =in.

To find deflection at point A and B

cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.4 ermine: he beam deflection at point A. he beam deflection at point B. ume Ma = 180 kip-ft, P = 12 kips, Lab = 3.8 ft, LBc = 5.7 ft. P A B C LAB LBC wer: = in.

cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.4 ermine: he beam deflection at point A. he beam deflection at point B. ume Ma = 180 kip-ft, P = 12 kips, Lab = 3.8 ft, LBc = 5.7 ft. P A B C LAB LBC wer: = in.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.8P

See similar textbooks

Related questions

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

Q: A variable cross-sectional beam is pinned from the point B by BD bar as shown. Flexural rigidity of…

Q: Rigid bar ABCD is loaded and supported as shown. Bars (1) and (2) are unstressed before the load P…

Q: 12. An aluminium (E = 70 GPa) column built into the ground has length, L = 3.0 m, and is under axial…

Q: Learning Goal: To determine an l-beam's maximum bending moment, moment of inertia using the…

A: Finding out the free body diagram and moment and bending stress.

Q: Select an IPE profile for the loading case shown in the figure. Se- lect this IPE profile from the…

Q: Consider the simply supported truss as defined in the figure and parameter table. Find the force in…

Q: composite shaft AC is made by shrink-fitting a titanium-alloy sleeve of length L3 = 4 ft over…

A: (a) Angle of Rotation at B (θB):Using the Displacement Method, we can calculate the angular…

Q: A prismatic bar is fixed at edges A and B as shown in figure. What is the axial force in CD portion?…

A: Given data- A prismatic bar fixed at edges A & B as shown- To Find- The value of the axial…

Q: 2. Given a simply supported beam shown in figure below with the cross section at maximum moment. The…

A: Given data:

Q: A #2 Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106)…

A: Given: Required: Slope and deflection at C

Q: What maximum load P can be applied without exceeding an allowable stress of 70 MPa for aluminum or…

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

Q: A simply supported beam, circular in cross section, of span L supports a point load Wat mid span.…

A: A simply supported beam, circular in cross-section, of span L.A point load W applied at the…

Question

The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1860 in.“]. For the loading shown,
determine:
(a) the beam deflection at point A.
(b) the beam deflection at point B.
Assume MA = 180 kip-ft, P = 12 kips, LAB = 3.8 ft, LBC = 5.7 ft.
MA
A
B
LAB
LBC
Answer:
(a) VA =
in.
(b) VB =
in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The frame shown in Figure P4.7-8 is unbraced, and bending is about the x-axis of the members. All beams areW1835, and all columns areW1054. a. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. c. If Fy=50 ksi, is the stiffness reduction factor applicable to these columns?
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.