Can you provide me the step by step process of this? Thank you! A simply supported timber beam with length L = 6 m carries a uniformly distributed load w = 8 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 6-m span length. A simply supported timber beam with length L = 6 m carries a uniformly distributed load w = 8 kN/m. Determine the magnitude of themaximum compression bending stress that occurs in the beam at any location within the 6-m span length.300 mmAВL100 mmO 24.00 MPaO 19.75 MPaO 16.98 MPaO 22.05 MPaO 32.62 MPa

Answered: Image /qna-images/answer/efdbc250-7ae4-4f0b-ab16-776a686399c9.jpg

Can you provide me the step by step process of this? Thank you! A simply supported timber beam with length L = 6 m carries a uniformly distributed load w = 8 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 6-m span length.

Can you provide me the step by step process of this? Thank you! A simply supported timber beam with length L = 6 m carries a uniformly distributed load w = 8 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 6-m span length.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 50 mm diameter circular bar is used as a simply supported beam 3 m long. Applied the uniforme distributed load ( 600 KN/m ) over the right two - thirds of the beam. Determine: (a) draw shear force and .moment diagrams. ( b) flexural stress *
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
The composite beam in Fig. a is made of wood and reinforced with a steel strap located on its bottom side. If the beam is subjected to a bending moment of M = 2 kN # m, determine the normal stress at points B and C. Take Ew = 12 GPa and Est = 200 GPa.
Determine the reactions at supports and then draw the shear force and bending moment diagrams for the beam shown below and determine the size of the beam if it has a rectangular cross section where the height is 3 times the width. Allowable bending stress is 80 MPa. 8 kN 3000 15 kNm 3 kN/m 2000 Width Height (3 x width) Section through beam
A simply supported wood beam with a span of L = 18 ft supports a uniformly distributed load w. The beam width is b = 5 in. and the beam height is h= 12 in. The allowable bending stress of the wood is 1020 psi. Determine the magnitude of the maximum load w that may be carried by the beam. |h Answer: w = i Ib/ft.
A 200 mm square hollow section at 15 mm thick, is used as simply supported beam both ends. The simple beam carries 10 kN/m uniformly distributed load applied on its entire span. Determine the maximum flexural stress (kPa) caused by the uniform load.
Problem 4: Determine the minimum height h of the beam shown in Fig. if the flexural stress exceed 20 MPa. 5 KN I= bh² 2 m mg. 2.5 kN/m ↑ Rislo 80 mm 1m ↓ 3m R₂
An overhanging beam is loaded as indicated. In order to accommodate communication cables to be installed later the beam is manufactured with two circular channels running through its length. The beam has a weight of q = 300 N/m. Calculate (a) the value and position of the maximum bending moment and sketch the relevant bending moment and shear force diagrams, (b) the position of the neutral axis, and (c) the maximum compressive and tension stress in the beam due to the bending. 2m 3 KN 3m B Bm 1 KN 100 mm 100 mm 20 mm H 30 mm
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
The cross-sectional dimensions of a beam are shown. Assume b=3 in., tetw=0.4375 in. and d=3.375 in. (a) If the bending stress at point K is 1860 psi (T), determine the internal bending moment M, acting about the z centroidal axis of the beam. (b) Determine the bending stress oH at point H (positive if tension, negative if compression). K d H bf Answers: (a) M2 = i Ib-ft. ( b) σμ i psi. %3D Save for Later Attempts: 0 of 1 used Submit Answer
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=14.0 ft, b=3.0 ft, c= 7.0 ft, w = 9 kips/ft and M = 300 kip-ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. " " Answers: Ay= Cy= b Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) i W i a W M a B M B ес b kips kips с Cy с X с -X
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 40.4 ksi. Assume P = 51 kips, L1=6.6 ft, and L2=19.8 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this beam. (c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?