Calculate the working values of the following circuits from the parameters in the given table. parameter R18 R19 R20 R21 R22 V6 V7 work value 15 kΩ30 kΩ 10 κΩ 10 κΩ 30 kΩ 10 mV 20 mV R19 R22 R18 R20 VO + R21 V6 U6 U7 V7 3.1 Calculate the rate of expansion U6 : Answer.. 3.2 Calculate the rate of expansion U7 : Answer.. 3.3 Calculate the total gain of U6 and U7 : Answer 3.4 Calculate the value of the output voltage U7 : Answer.. 35 Calculate the value of the outnuut veltege VO:A

Calculate the working values of the following circuits from the parameters in the given table. parameter R18 R19 R20 R21 R22 V6 V7 work value 15 kΩ30 kΩ 10 κΩ 10 κΩ 30 kΩ 10 mV 20 mV R19 R22 R18 R20 VO + R21 V6 U6 U7 V7 3.1 Calculate the rate of expansion U6 : Answer.. 3.2 Calculate the rate of expansion U7 : Answer.. 3.3 Calculate the total gain of U6 and U7 : Answer 3.4 Calculate the value of the output voltage U7 : Answer.. 35 Calculate the value of the outnuut veltege VO:A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2
i need the answer quickly
O b. None of them C. Req=36.67 Q,P=-3.92W. O d. Req=61.5 Q,P=-2.34W. e. Req=36 0,P=-4W. estion 4 For this circuit, the values of 11, 12 and V are: yet swered 11 12 arked out of R1 R2 R3 R4 Is 15 A V 50 10 Q 10 Q Flag uestion Select one: O a. 11= 10J12 = 5 A, V=50 V O b. 11 = 5 A, 12 = 2.5 A, V=25 V O c. 11 = 5 A, 12 = 2.5, V=50 V O d. 11 = 2.5 A, 12 = 5 A, V=25 V Question 5 Find Rab- Not yet arswered 20 Q AAAA Marked our of TOSHIBA
S:11)
only 4 please
1/C1 1/C2a 1/C2b 1/C3a 1/C3b OTR O PRE D 74574N/1 CLK O CLR O PRE O PRE D 74574N/ CLK O CLR Q Q Q O PRE R. DIS S55 THRO PASTAN/1 74574N/2 CLK Q 74574N/2 CLK Q CV GRD V+ a CLR O CLR 100µF LED2 7 LED3 V LED4 V LEDS A V LED1 wwD ww ww ww
V1 R1 V2 Da Db R2 www V3 Given that R1=2k, R2=1k, and Da and Db are Si Diodes: a. What is V3 in terms of V1 when Da is ON? b. What is V3 in terms of V1 when Db is ON? c. What is V3 in terms of V1 when Da and Db is OFF?
V2
3. For the circuit shown, calculate the input voltage if the output voltage is 10.08 V. 10KO 5KN SKO 10OKO SKO 5KN V1 Va Vo NON-INVERTING INVERTING INVERTING
What is the peak positive output voltage to the load resistor? (Units are in Volts.) What is the peak negative output voltage to the load resistor? (Units are in Volts.) Please in typing format please ASAP for
For the given circuit and input waveform determine the output waveform. a. b. C. d. a b 15 20 d -10 20 OC 20 -5 5 ▷ 2.2 k 5 V பப Dj 20 pun m UL n 11.
Q3) Draw the output signal of the circuit shown in Figure 1 R1 ww 2000 R4 m 5KQ V4 R2 U1 2V 10k0 5 V1 2Vrms 1Hz 0 Figure 1 R3 m 10k0 Vout