Calculate the overall heat transfer coefficient of the steel pipe based on the inner surface. The inner diameter of the pipe is 12.7 cm, and the thickness of the pipe is 2.4 cm. The convection heat transfer coefficient in the pipe is 350 W / (m² ° C), the convective heat transfer coefficient outside the pipe is 25 W / (m² ° C), the thermal conductivity of the steel pipe is 15 W / (m ° C). If the pipe is used to deliver steam at 110 ° C and the ambient temperature is 20 ° C, determine the heat transfer rate of the pipe per meter. q = Watt / m

Q: A long, thin copper rod 5 mm in diameter is exposed to an environment at 20°C. The base temperature…

A:

Q: Consider a copper tube with domestic hot water flowing inside (Tin =70◦C, um = 0.5m/s). The inner…

A:

Q: A long copper (k = 200 W/m-K) tube has an inner radius o Refrigerant flows through the pipe. The…

A:

Q: Blowtorch is used to connect the two pipes together. Length of the pipe section shown is 95 cm with…

A: Given: l=0.95m; d=0.65m; t=2.5mm k=157 W/m2K; ambient temperature 20 deg C; h=20 W/mC; and melting…

Q: A cylindrical tank is constructed from aluminum (kal = 240 W/m2.K) with 1 m inner diameter and 10 mm…

A:

Q: 1. A residential building has height of 50 m and floor area (25 m x 30 m) as shown in figure below.…

A: Given data,Tout=0°CTin =22°CAir required=36m3/hrRoof area=25×30=750m2

Q: a flat wall is covered with a layer of insulation 1.0 in. thick whose thermal conductivity is 0.8…

A:

Q: A surface has an area of 46 m^3 . It is 36mm thick and has a thermal conductivity of 0.95 W m^-1…

A:

Q: (a) Determine the temperature at tip of spoon handle assuming heat transfer from the tip of the…

A: The thermal conductivity of stainless steel is The cross section area of spoon is The heat transfer…

Q: If the rate of heat flow through a furnace wall is 0.94 kW/m². The wall consisting of 0.20 m thick…

A:

Q: Airat temperature of 120 °C is contained in a thin-wall steel tube with heat-transfer coefficient 65…

A: Dear student, I have calculated overall heat transfer coefficient on the basis of inner and outer…

Q: copper tube (k-75 W/m*K) with inner radius r;-2 cm and outer radius r22.05 cm is used to transport a…

A:

Q: Consider a steam pipe of length L = 20 m, inner radius r₁ = 6 cm, outer radius r₂ = 12 cm, and…

A:

Q: A steel pipe (k = 48 W/m∙K) of a heating system carries wet steam at 125 °C. The inner and outer…

A:

Q: A cylindrical tube with inner and outer radius are 10 mm and 20 mm respectively and the temperature…

A:

Q: none

A:

Q: Blowtorch is used to connect the two pipes together. Length of the pipe section shown is 80 cm with…

A: Given: l=0.8m; d=0.7m; t=3mm; k=177 W/m2K; ambient temperature is 25 C; h=20 W/mK; Tb=220 C

Q: If the average connective heat transfer coefficient on the outer surfaçe of a tube (inner diameter =…

A:

Q: 12 = 40 cm and 13 = 80 cm, respectively. The leng is 1 meter. The thermal conductivity of the wall…

A:

Q: 10 hot rods (L = 5 m and d = 2 cm) are buried in the ground parallel to each other each rod is 10 cm…

A: The given information in the problem is shown in the following attached image:

Q: A hot-water pipe (k = 60 W/m K) in a house, made of 3/4-inch schedule 40 pipe (OD = 26.7 mm;…

A: To find: The percentage reduction in heat loss. Given: The inner radius of the pipe is r1=10.48 mm1…

Q: An internal engine of a rocket (180°C furnace) generates heat flow of 23.2564 kW through a first…

A: ◆ This is the case of heat transfer through the cylindrical layer.  ◆ The temperature profile for…

Q: Heat Transfer Consider a infinitely long pin fin with uniform Ac cross sectional area Write ef…

A: Given data Write effectiveness and efficiency for infinitely long pin fin with uniform Ac cross…

Q: Question 6 A steel pipe (k = 48 W/m-K) of a heating system carries wet steam at 120 °C. The inner…

A: Given: The conductivity of steel pipe is k1=48 W/m·K. The temperature of the steam is T1=120°C. The…

Q: A cast iron pipe is used to transfer steam with an inlet temperature of 300 C. Inner radius of the…

A:

Q: Q₁: Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k-2.3 W/m °C, and…

A: Given data:- Plane wall thickness, Thermal conductivity of wall,  and its surface area, The left…

Q: A liquid food is being pumped in a 1 cm thick steel pipe. The inside diameter of the pipe is 5 cm.…

A: “Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: The composition of a symmetric composite wall is shown in figure below hi 7 T1 1 2 Brick Brick Brick…

A: Given; k1=k5=0.026 W/m°Ck2=k4=0.22 W/m°Ch2=25026 W/m2°Ch1=10026 W/m2°CT∞1=20°CT∞2=100 °C Let the…

Q: Consider a conduction in a plane composite wall as shown. The outer hotter air temperature at 60 C…

A:

Q: A cast iron pipe is used to transfer steam with an inlet temperature of 300 C. Inner radius of the…

A:

Q: PROBLEM 3 In the given schematic of heat transfer for a wall, there is heat conduction through the…

A: For the solution refer below images.

Q: n internal engine of a rocket (180°C furnace) generates heat flow of 23.2564 kW through a first…

A: Given:Ti=180°CQ=23.2564 KWd1=3 mt1=0.0065 mk1=0.6 W/m.Kt2=0.05 mk2=0.16 W/mLTo=12°C

Q: Steam at 350 °C flows through the stainless steel pipe with k=26 W/m.°C. The inner and outer…

A:

Q: Steam at 180 0C flows in a circular pipe, which is composed of 3 different materials (A, B and C).…

A:

Q: A 90-amp electric current is flowing through a 6-mm diameter lead wire. The thermal conductivity of…

A:

Q: fin made of AL metal with thermal conductivity (199 W / mK). Fin dimensions 3 cm long and 2.5 mm…

A: given data: fin metal : Al : k = 199 W/mK length; l = 0.03 m thickness; t = 2.5 mm wall temperature;…

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.