What is the product of overall heat transfer coefficient and area (UA) for a heat transfer equipment with the geometry as shown in the diagram? The inner tube (the shaded area in the figure) is made of a material with thermal conductivity of 1.2 W/m.K. The convection coefficient of the hot fluid (in the inner tube) is 25 W/m².K and that of the cold fluid is 12 W/m².K. The dimensions shown in the figure are r₁ = 0.1 m, r2 = 0.15 m, and r3 = 0.3 m. The length is 1 m. 4.86 W/k r3 Cold Fluid Hot Fluid

What is the product of overall heat transfer coefficient and area (UA) for a heat transfer equipment with the geometry as shown in the diagram? The inner tube (the shaded area in the figure) is made of a material with thermal conductivity of 1.2 W/m.K. The convection coefficient of the hot fluid (in the inner tube) is 25 W/m².K and that of the cold fluid is 12 W/m².K. The dimensions shown in the figure are r₁ = 0.1 m, r2 = 0.15 m, and r3 = 0.3 m. The length is 1 m. 4.86 W/k r3 Cold Fluid Hot Fluid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heat transfer
A 10-in.-OD mild-steel pipe of 1/2 in. wall thickness is covered by two layers of insulating materials. This pipe is used to convey heated air in a test arrangement and is not a permanent installation. See figure below. Determine the following: a. Determine the heat transfer rate per lineal foot of pipe. b. Determine T3. 1000°F MITIMIDA 7=32°F 1-in.-high temperature insulation, k = 0.051 Btu/h ft °F 1 in. 85% magnesia
Q: Consider the section of multilayers wall as shown in the figure, assuming one dimensional heat flow, determine the following: I- The thickness of wall layers L1 and L2 as shown in the figure. II- Inner and outer surface temperatures T1 and T3 III- Rate of heat transfer per unit area (Im² ) through the wall. T01 = 320 °C T02 = 20 °C T1 T2 T3 T2 = 240 °C hi = 300 W/m².°C k1 k2 h2 = 50 W/m².°C %3D Too1 T2 k1 10 W/m .ºC hi h2 k2 = 0.5 W/m .ºC %3D L = 40 cm L1 L2 L
3-78 Circular aluminum disk fins of constant rectangular profile are attached to a tube having D - 25 cm outside diamcter with a spacing of 8 mm (that is, 125 fins per l-m tube length). Fins have a thickness t-I mm, beight L- 15 mm, and thermal conductivity k- 200 W/(m- °C). The tube wall is main- tained at a temperature T, = 190°C, and the fins dissipate hcat by convection into ambient air at T. = 40°C with a heat transfer cocfficient h = 80 W/(m.°C). (a) Determine the fin efficiency. (b) Determine the area-weighted fin efficiency. (c) Determine the net heat loss per t-m length of tube. (d) What would be the heat loss per 1-m length of tube if no fins were attached?
Heat Transfer
1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.08 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are h; = 18,000 W/m²-K and ho = 12 W/m²-K. Determine the heat loss (kJ/min) from 4 m of pipe. • show conversions, units, and box in your final answers
HEAT TRANSFER: A thick-walled nuclear coolant pipe (k = 12.5 Btu/hr-ft-°F) with 10 in. inside diameter and 12 in. outside diameter is covered with a 3 in. layer of asbestos insulation (k 0.14 = Btu/hr-ft-°F). If the inside wall temperature of the pipe is maintained at 550°F, (a) calculate the heat loss per foot of length. The outside temperature is 100°F. (b) Find the interface temperature between the pipe and the insulation.
Q: Consider the section of wall as shown in the figure, assuming one dimensional heat flow, determine the following: I- Rate of heat transfer per unit area (Im²) through the composite wall. II- Determine also the temperature (Tp) as shown in the figure. To1 30 °C Too2 = 2 °C hi = 20 W/m?.C 8 cm h2 = 12 w/m?.C 20 cm A %3D kA = 0.6 W/m.°C D TD %3D 30 cm kB = 0.8 W/m .°C T01 To2 kC = 0.9 W/m.°C hi B E 10 cm h2 kD = 0.7 W/m .°C kE = 0.5 W/m.°C %3D kF = 0.04 W/m.C 8 cm 6cm. 12cm
4
can you please please work it all out
In the given figure, cylindrical fins of circular cross section with a rectangular profile are attached to a hollow cylindrical element. Values are given on the figure. According to thisa) The efficiency and effectiveness of the blade b) Calculate the amount of heat transfer per unit length for N=100 blades.
Can someone please help me with creating an excel spreadsheet to calculate heat transfer phenomenon from a cylindrical fuel rod to the coolant? The excel sheet needs to be able to calculate these 3 things: Heat generated in a fuel rod at a distance ‘r’ from the center; Total Heat generated in the Reactor; the maximum temperature in the fuel and the cladding surface temperature, for a fuel rod at a distance ‘r’ from the center. The fuel used in this will be UO2 and there is a thin layer of helium that will separate the fuel from the cladding material. The user input parameters will be: the thermal neutron flux at the core, thermal conductivity of fuel, thermal conductivity of helium, thermal conductivity of the cladding, thickness of the helium layer, thickness of the cladding, diameter of the fuel pellet, fuel rod location (r), Cylindrical Reactor Size, and the fuel enrichment. For the fluid the user input will be coolant temperature and the heat transfer coefficient.