Exercise 7 3-34 The wall of a refrigerator is constructed of fiberglass insulation (k=0.035 W/m K) sandwiched between two layers of 1-mm-thick sheet metal (k = 15.1 W/m-K). The refrigerated space is maintained at 2°C, and the average heat transfer coef- ficients at the inner and outer surfaces of the wall are 4 W/m²-K and 9 W/m²K, respectively. The kitchen temperature aver- ages 24°C. It is observed that condensation occurs on the outer surfaces of the refrigerator when the temperature of the outer surface drops to 20°C. Determine the minimum thickness of fiberglass insulation that needs to be used in the wall order to avoid condensation on the outer surfaces. Kitchen air 24°C 1 mm Sheet metal Insulation Refrigerated space 2°C mm

Exercise 7 3-34 The wall of a refrigerator is constructed of fiberglass insulation (k=0.035 W/m K) sandwiched between two layers of 1-mm-thick sheet metal (k = 15.1 W/m-K). The refrigerated space is maintained at 2°C, and the average heat transfer coef- ficients at the inner and outer surfaces of the wall are 4 W/m²-K and 9 W/m²K, respectively. The kitchen temperature aver- ages 24°C. It is observed that condensation occurs on the outer surfaces of the refrigerator when the temperature of the outer surface drops to 20°C. Determine the minimum thickness of fiberglass insulation that needs to be used in the wall order to avoid condensation on the outer surfaces. Kitchen air 24°C 1 mm Sheet metal Insulation Refrigerated space 2°C mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a permanent one-dimensional heat conduction on a flat wall of length L = 0.4 m and constant thermal conductivity equal to 0.9 W/m.K, without heat generation. a) If the inner wall is T(0) = 140°C and receives a constant thermal flux of q', = 400 W/m?, what is the temperature at the outer surface, T(L) = ? b) If T(0) = 50°C and the outside of the wall is exposed to air convection at 25°C and h=10 W/k.m?, what is the temperature on the outside surface, T(L)?
Pr
can you please please do this one and please show all the work please step by step
. Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k = 2.3 W/m °C, and surface area A = 20 m². The left side of the wall is maintained at a constant tem- perature of T₁ = 80°C while the right side loses heat by con- vection to the surrounding air at T = 15°C with a heat transfer coefficient of h = 24 W/m². °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat trans- fer through the wall. Answer: (c) 6030 W
Consider a power transistor encapsulated in an aluminum case that is attached at its base to a square aluminum plate of thermal conductivity k= 240W/m.K, thickness L= 6mm, and width W= 20mm. The case is joined to the plate by screws that maintain a contact pressure of 1 bar, and the back surface of the plate transfers heat by natural convection and radiation to ambient air and large surroundings at T∞ =Tsur -25°C. The surface has an emissivity of ε=0.9, and the convection coefficient is h=4 W/m².K. The case is completely enclosed such that heat transfer may be assumed to occur exclusively through the base plate. a) If the air-filled aluminum-to-aluminum interface is characterized by an area of A₁=2×10-4 m² and contact resistance of R+c= 1.375 K/W, what is the maximum allowable power dissipation if the surface temperature of the case, Ts,c, is not to exceed 85°C? S,C' Transistor case Ts. Pelec S,C' Enclosure W Isur Base plate, (k,ε) Interface, Ac Air Th 801 b) How much should the h be…
In the walls of a warehouse, the inner plaster thickness is 2 cm and the heat conduction coefficient is 0.60 W / moC, the curtain concrete thickness is 10 cm, the heat conduction coefficient is 1.3 W / moC, the outer plaster is 2.5 cm and the heat conduction coefficient is 1.2 W. It is known to be / moC. Inner surface heat transfer coefficient is 8 W / m2oC and outer surface heat transfer coefficient is 21 W / m2oC. Indoor temperature, outdoor temperature and relative humidity of indoor environment are given in the table. How much of the insulation material with thermal conductivity coefficient should be used between the gas concrete and the outer plaster in order to prevent condensation on the inner wall of this warehouse. The indoor and outdoor ambient temperatures of the warehouse and the relative humidity of the storage environment are given in the table.K insulation: 0.032T inner: 14T outside: -15Relative humidity: 60
SOlve asap plz
I need complete solutions and 4 decimal places in all solutions.
Its thickness is 1.18 m, its thermal conductivity is 2.75 W/m.°C and its surface area is 15m2Consider a wide plane wall. Inside of the base plateThere is a uniform heat flux produced on its surface with the help of the resistance wire inside.590 W/m2 on the left surface of the wall at x=0net heat fluxand the temperature on this surface was measured as 590 °C. On the wallassuming that there is no heat generation and that the thermal conductivity is constant;a) The differential equation for continuous one-dimensional heat conduction in the wall, andSet the boundary conditions.b) Solve the differential equation to obtain a relation for the temperature change at the wall.c) Calculate the heat loss rate from the wall.
Q4/A 2-mm-diameter and 10-m-long electric wire is tightly wrapped with a 1-mm-thick plastic cover whose thermal conductivity is k-0.15 W/m "C. Electrical measurements indicate that a current of 10 A passes through the wire and there is a voltage drop of 8 V along the wire. If the insulated wire is exposed to a medium at Ts= 30°C with a heat transfer coefficient of h-24 W/m² C, determine the temperature at the interface of the wire and the plastic cover in steady operation. Also find the critical radius of plastic insulation. [334 T=30°C Electrical wire Insulation bale 10 m