Calculate the overall heat transfer coefficient for the following cases:(a) Heat is transferred across Im?of a 3-cm thick plate made of steel of k = 36.4 W/(m-K). A liquid flows on one side with a heat transfer coefficient h, = 4000 W/(m2K) and the other side is exposed to air with hy= 12W/(m²-K). Assume a foul-ing heat transfer coefficient of h,- 3000 W/(m-K) on the liquid side.(b) Same as part (a), with the air replaced by condensing steam, h, = 6000 W/(m2K).() Same as part (a) with the liquid replaced by a flowing gas, h = 6 W/(m2K).%3D%3D

Answered: Image /qna-images/answer/050d69e3-8249-46e2-b834-8736f0835b9c.jpg

Answered: Calculate the overall heat transfer…

Engineering

Mechanical Engineering

Calculate the overall heat transfer coefficient for the following cases:

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.49P

See similar textbooks

Similar questions

An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient temperature is 21°C, and the surface heat transfer coefficient is . How long after the iron is plugged in does its temperature reach 104°C?
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
What is true answer
B- A Blood warming device contains a 20 mm diameter copper pipe is used to carry warm water, the external surface of the pipe is subjected to convective heated transfer coefficient of h 6 W/m² K, find the heat loss by convection per meter length of the pipe when the external °C and surface temperature is 40 the surrounding are at 20 °C.?
I need the answer as soon as possible
Outer surface of a tube-steel oven is at 110 oC. What would be the heat transfer rate tothe surrounding air at 25 oC. if the natural convective heat transfer coefficient ish = C (Ts – Ta)1/4where; C= 4.5 W/(m2.K5/4), Ta and Ts are air temperature and surface temperature,respectively. Surface area of the wall is 125 m2.(heat transfer by radiation can be neglected)
Hot water (specific heat of 4.18 Kj/kgK) at 66C is flowing through a metal pipe (6 m long, 2 cm ID, 2.75 OD, thermal conductivity of 4.7 W/mK). The pipe is directly under an HVAC vent, and air at 21C is being blown over the pipe. This results in a conductive heat transfer coefficient of 129 W/m²K. If the convective heat transfer coefficient between the water and the pipe is 350 W/m²K, what is the overall heat transfer coefficient? What is the rate of heat 5. transfer from the water to the air?
S is 6. A spherical shaped vessel of 1.4 m outer diameter is 90 mm thick. Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220°C. Thermal conductivity of the material of the sphere is 0.083 W/mK. (a) 0.2 kW (c) 1.088 kW (b) 0.5 kW (d) 1.6 kW
An electric motor is to be connected by a horizontal steel shaft (k 42.56 W/m.K), 25 mm in diameter to an impeller of a pump, circulating liquid metal at a temperature of 540°C. If the temperature of electric motor is limited to a maximum value of 52°C with the ambient air at 27°C and heat transfer coefficient of 40.7 W/m2.K, what length of shaft should be specified between the motor and pump? Steel shaft
i need the answer quickly
Solve it pls.