Calculate the number of days required to dig a dirt road with a length of (4 km), a width of 300 cm) and a thickness of (0.2m), using two excavators, if you know that each excavator works with two vehicles with a capacity of (10) m3 in the measure of looseness and each of them, in order to transport the soil excavations outside The site, and the productivity of one cart in the bank scale (16 m3/hr) and the soil density in the loose and bank scale are (1450kg/m, (1350kg/m3), respectively: Also, the efficiency of the cart (90) and the number of working hours per day (7) hours?

Calculate the number of days required to dig a dirt road with a length of (4 km), a width of 300 cm) and a thickness of (0.2m), using two excavators, if you know that each excavator works with two vehicles with a capacity of (10) m3 in the measure of looseness and each of them, in order to transport the soil excavations outside The site, and the productivity of one cart in the bank scale (16 m3/hr) and the soil density in the loose and bank scale are (1450kg/m, (1350kg/m3), respectively: Also, the efficiency of the cart (90) and the number of working hours per day (7) hours?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the quarry productivity per hour for the quarry under the following conditions: • The length of the blade is (2.9) m, the width of the blade is (0.9) m. Clay sandy soil weighing (1601.8) kg / m on the bank scale. soil swelling coefficient (25%) . The transportation distance is (30) meters on flat ground Push-to-go speed is (2.4) km/h. Push back speed (5.6) km/h. The estimated power of the slingshot engine is (72) hp. Actual working minutes per hour Fixed time (0.32) minutes.
Compute the volume of 10 m deep pit whose top and bottom dimension are 5m x 4m and 10 m x 8 m.
Convert 2300BCM of clay to a volume in loose measure. Convert 1700LCM of common earth to a volume in compacted measure (CCM). Calculate the volume of sand and gravel (in LCM) needed to fill a ditch that is 2km x 3m x 1.5m. The sand and gravel will be compacted.
Choose the correct answer
Plz,answer both parts, a and b. Geotechnical Engineering-1 Q.1a)Discuss the factors that contribute to Hydraulic conductivity in detail? b)Explain in detail the factors that are responsible to achieve the desired level of compaction?
An approach road for a bridge needs 60000 m3 of soil compacted to a void ratio of 0.7. There are two borrow pits A and B from where the required soil can be taken and transported to the site. The borrow pit A has void ratio 0.85 and borrow pit B has void ratio 0.95. If the cost of excavation of soiland transportation is Rs. 20/10 m3for area A and Rs. 22/10 m3for area B, which of the borrow area is more economical? G=2.67
QI/ A contractor excavates 10,000 m soil at moist unit weight of 17.5 kN/m' and moisture content of 10% from a borrow pit and transports it to a project site. The project has an area of 20,000 m2 to be filled with this compacted soil. If the required dry unit weight and moisture content of the compacted soil are 18.3 kN/m and 12.5% (assume there is no soil loss during transportation and compaction), what is the thickness of the compacted soil and how much water needs to be added?
Quantities refers to the estimated amounts of labour and materials required in the execution of the various items of work, and together these items give the total requirements of the contract. 3.1 The concrete foundation block shown in figure 1 is excavated into shape. Calculate the net excavation quantity and the quantity of 30 MPa concrete in the block. 1.50 m 1.00 m 1.50 m 2.00 m Figure 1: Concrete Foundation Block 2.00m
- Once answered correctly will UPVOTE!!