Calculate the fault current in each phase for a L-G fault occurs at machine-2 for the system shown in below fig.below.All the reactances are given in p.u on 100 MVA base. E- 16º * = j0.2 X2 = 10.22 X = 30.15 Line X, -x - j0.11 Xp = j0.33 - j0.16 X = 0.17 Xo = j0.06 X, =x2 = j0.10 X =x2 = Xg = 0.10 ele

Calculate the fault current in each phase for a L-G fault occurs at machine-2 for the system shown in below fig.below.All the reactances are given in p.u on 100 MVA base. E- 16º * = j0.2 X2 = 10.22 X = 30.15 Line X, -x - j0.11 Xp = j0.33 - j0.16 X = 0.17 Xo = j0.06 X, =x2 = j0.10 X =x2 = Xg = 0.10 ele

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the fault current in each phase for a L-G fault occurs at bus at machine-2 for the system shown in below fig.All the reactaces are given in p.u on 100 MVA base E = 16º. Line x4 = j0.2 X1 = x2 = j0.11 Xp = j0.33 X2 = J0.2 X4 - j0.16 X = 30. 25 X2 = J0.16 Xo = j0.06 X1 = X2 = j0.10 X1 =X2 = Xo = 0.10 j1.8847p.u None -j1.7747p.u -j1.4487p.u
In single line diagram of substation, the following symbol is used for of tion O Lightning arrester O Current transformer O Air blast circuit breaker O Potential transformer W
Single line to ground fault of a solidly grounded generator positive sequence current is j2.5 p.u, then the current flow in the neutral during the fault is O j1.05 p.u O jo.25 p.u O j2.5 p.u O j7.5 p.u
(Q.2) For the following network, calculate the fault currents (IF1, IF2, IF3 and IF.) in pu and in kA, and fault MVA (ie. short-circuit level) at the indicated locations. Internal reactance of generators are j0.9 pu. Base quantities: 11 kV, 400 MVA on the generator side. 113.3 kV 4 MVA, 7% j0.5 2 j0.4 2 300 A 200 A 11 KV 250 MVA
33
(please solve within 20 minutes i will give thumbs up thanks)
Calculate the fault current in each phase for a L-G fault occurs at primary of transformer-2 for the system shown in below fig.All the reactaces are given in p.u on 100 MVA base E= 1/0º x = j0.2 Line X =x, = j0.11 Xp = j0.33 X2 = ]0.22 xe = 30.15 - j0.16 X2 = J0.17 Xo = j0.06 X, = x2 = j0.10 X1 =x2 = xg = 0.10 -j2.7831 -j2.3781p.u None -j2.2668 p.u ele
B1
a) In Three Phase Faults that will occur separately on A, B, C and D Busbars, Calculate the currents. b) Maximum fault currents to pass through KA, KB, KC1, KC and KD Protection devices determine. Help me please... Thank you so much.
The negative sequence current of a solidly grounded generator for single line to ground fault is j 2.5 p.u. Then the positive sequence current during the fault is equal to o j7.5 pu o jo.75 pu o j2.5 pu o jo.25p.u
Please show complete solutions
Q5: (A) A 100 KVsurge travels on an overhead line of surge impedance 400 Q.The line is connected to a cable of surge impedance 50 Q through a resistance R. Find (1) the value of R that it absorbs maximum energy, and (2) voltage and current transmitted into cable? (B) Explain in details the following phrase (The rate of rise of re-striking voltage will become high if the fault ocurrs near the bus bar of the station?