HW2A vertical concrete pipe of length L= 1.0 m, outside diameter dout = 15 cm, insidediameter din = 10 cm is compressed by an axial force F = 1.2 kN as shown inFigure 4.5. Assuming the modulus of elasticity of concrete to be E = 25 GPa andPoisson's ratio as v = 0.18, determine:!!(a) the(b) tne(c) The increase in the outer and inner diameters Ddout and Ddin(d) The increase in the pipe wall thickness Dt(e) The percentage change in the volume of the tube (DV / V) 100.1.2 KN1.0 m15 cm10 cm

Answered: Image /qna-images/answer/5e8dee7d-9ea9-4343-a1ed-fac1e5b83993.jpg

Answered: c) The increase in the outer and inner…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which of the following velocity profiles best resembles fully-developed turbulent flow in a pipe? A) B) D
Water is pumped at a rate 500 litres per minute through a 1 km horizontal, circular pipe of diameter 20 cm. The pipe has a friction factor of 0.05. a) Calculate the average velocity in the pipe. b) Determine the Reynolds number in the pipe and explain what the flow regime is. c) Determine the pressure loss along the length of the pipe. d) Determine the power a pump would need to supply in order to overcome the friction in the pipe.
ENGINEERING HYDRAULICS
Please explain all intermediate steps. Thanks you
TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS. I'LL DOWNVOTE.
4. Testing, adjusting, and balancing is a prerequisite before starting-up of an air-conditioning system used for public areas. To perform this, it is needed to measure the flow rate available within the system. What would you prefer to use in such a measurement? A) Pitot- static Tube B) Thermal (Hot-Wire and Hot-Film) Anemometers C) PIV D) Pitot Tube
Q2) bag house filter contains 135 cylindrical filter of 0.19m diameter and 9 m height the running time before cleaning is lhr dust load is 5 gr/ft, pe =1.1 gr/cm gas flow rate to the filter 3 x 104 m/h what is the maximum thickness of the cake
A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing process, both pastes are pumped through a pipe, with the red paste lying in the centre of the pipe, as shown in Figure Q2. The pipe has an internal radius, R₂, and the segment of red paste has a radius R₁. The flow is found to follow the Poiseuille equation, i.e. u(r) = I - 1 dp 4µ dx (R2² - r²) Where u is the viscosity of the paste and is the pressure gradient. The total flow of toothpaste through the pipe is Qtot, and the flowrate of the red paste is Qred. dx The toothpaste has a density of p = 1200 kg/m³, and a viscosity of 0.03 Pa.s. The pipe has a radius R₂ = 5 cm and a length L = 2 m. a) Find an expression for the flowrate of the red toothpaste. You answer should be in dp terms of μ, R₁, R₂, P) H, b) The flow in the pipe becomes turbulent when the Reynolds number reaches 2000 (where Re is calculated using the mean velocity across the pipe). What is the maximum pressure drop along the…
Solar concentrators are used to power a small village. Which one of these below is not important to generate the enough amount of power? a)Pipeline should be place at an appropriate distance from the concentrators and we can approach the problem as steady flow problem b)Nusselt number depends whether it is cooling or heating turbulent flow problem c)None of the above d)The thermal and velocity entry length can be found using Reynolds number and the diameter of the pipeline e)To find the maximum power, we can use the condenser and turbine inlet temperatures as reference. f)First law of thermodynamics is one of the important steps to solve the problem
Water flows, a stream line flow of, through a tube, of equal open ends, from its side to its right side. If the right end cross sectional area is increased by twice of its original area, then the speed of flow through the right end will be equal to a) 33.3% of its previous value, b) 300% of its previous value, c) 150% of its previous value, d) 100% of its previous value. Select one: O d a b
28. A differential mercury manometer is attached to a Venturi meter, as shown. At point 1, the diameter of the pipe is 16 cm while at point 2, the diameter of the throat is 6 cm. What is the water flow rate in the tube? Specific gravity of mercury is 13.6. 15 cm ↓ A) 0.021 m³/s B) 0.017 m³/s C) 0.012 m³/s D) 0.027 m³/s

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

c) The increase in the outer and inner diameters Ddout and Ddin d) The increase in the pipe wall thickness Dt e) The percentage change in the volume of the tube (DV / V) _100.