1.A fluid at a temperature of 28 oC flows at a speed of 10 m/s across a pipe outer diameter of 5 cm with a uniform surface temperature of 125 oC. Calculate coefficient the average heat transfer rate, and the rate of heat transfer per meter of pipe length if the fluid flow is: a) air at atmospheric pressure b) water c) ethylene glycol d) What is your discussion and conclusion?

1.A fluid at a temperature of 28 oC flows at a speed of 10 m/s across a pipe outer diameter of 5 cm with a uniform surface temperature of 125 oC. Calculate coefficient the average heat transfer rate, and the rate of heat transfer per meter of pipe length if the fluid flow is: a) air at atmospheric pressure b) water c) ethylene glycol d) What is your discussion and conclusion?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question A2 Figure QA2 is a schematic view of a river flow down an infinite hill with a constant angle of 0. Assume the viscosity and density of water are μ and prespectively. Furthermore assume in this motion the depth of the river remains unchanged and pressure is constant. a) List all the assumptions that you make in order to simplify the conservation of mass and N-S equations. b) Derive and list the simplified equations. c) Find a general solution to the velocity distribution across the river depth and then by applying the appropriate boundary conditions find an expression for the velocity profile. d) Determine the depth of the river in terms of volume flow rate Q per unit width. River bed y h Water Ꮎ Figure QA2 g
Water flows through a pipe at a velocity of 1 m/s. The pipe has a relative roughness of 0.001 and has a diameter of 100 mm. 1. Using the information provided above and in the Moody diagram, drag and drop circle labelled "1" (located below the graph) where the corresponding Reynolds number and relative roughness intersed 2. Drag and drop circle labelled "2" to the point on the y axis where you would read off the friction factor (f). v = 10-6 m²/s for H20 at 20°C. V.1V aminar.Critical low 0.09 zonc Transition zone 0.08 Complete turbulence, rough pipes 0.07 0.05 0.04 0.06 0.03 0.05 0.02 0.015 0.04 0.01 0.008 0.006 0.03 Res 0.004 0.025 0.002 0.001 0.0008 0.0006 0.0004 0.02 Smooth piper 0.015 0.0002 0.0001 0.000,05 0.01 0.009 0.000,01 10' 2(10) 3 4 56 8104 2(10) 3 4 56 S105 2(10) 3 4 56 $106 2(10) 3 4 56 S102(10) ³¸ 4 56 $10 0.008 Vd Reynolds number Re= -0.000,001 -0.000,005 Friction factor f= Relati ve roughness
Editing Q1. Three types of pin fins. The fins will be subjected to a gas in cross flow at v= 10 m/s. The cylindrical fin has a diameter of D 20 mm, and cross-sectional area is the same for each configuration shown in the sketch. V, T, V, T, V, T. Configuration A Configuration B Configuration C For fins of equal length and therefore equal mass, which fin has largest heat transfer rate? %3D Assume the gas properties are those at T (treat it as air) = 350 K. Hint: Assume the fin can be treated as infinitely long. D Focus stes)
Determine the resistance in each scenario presented. Explain whether the resistance is linear or not, and if not describe the relation, finally, explain how it can be linearized about a specific condition. Be sure to state the units and demonstrate that they are correct using the appropriate pressure/flow relation. a) Laminar flow An aqueous solution of 50% glycerol / 50% water is flowing through a pipe with the following system parameters: System_Parameters = (L = 100.0 D= 0.2 u= 0.022 p= 1150.0 9m=7.0 g = 9.81) units : L ~ m; D~ m; µ ~ Pa · s; p~ kg: 4. ~ 8: Confirm that this is laminar flow and then calculate the resistance. b) Pump Resistance from Pump Curve Consider the following pump curve: [Feet) (Meters] 30어 Find the pump resistance if the pump is supporting 15 meters of discharge head pressure, at a flow rate of 300 L/minute. 80- 250 7어 100 PSI L/min Determine the pump resistance in Pa 20어 6어85 PST 50 SCFM 5어 75 PST Note that standard pump curves are oriented opposite to the…
A venturi meter is used to measure the flow rate of water at 55 degrees Celsius. The venturi meter has a throat diameter of 75mm, and it is situated in a 250-mm pipeline. A mercury (SG = 13.6) manometer measures the pressure difference, and the reading is 24 mm. Determine a.) the Reynolds number of the flow, b.) the average velocity, c) the volumetric flow rate, and d.) the power loss if 12% of the pressure drop is permanently lost.
Subject : Thermofluid Question : Air at 20oC flows in a 0.60 m diameter pipe at a rate of 15 m3/s as shown in Figure 3. The pipe diameter changes to 1.2 m through a sudden expansion. i. Assess the pressure rise across this expansion. ii. Explain how there can be a pressure rise across the expansion when there is an energy loss (KL ≠ 0).
Water is pumped at a rate 500 litres per minute through a 1 km horizontal, circular pipe of diameter 20 cm. The pipe has a friction factor of 0.05. a) Calculate the average velocity in the pipe. b) Determine the Reynolds number in the pipe and explain what the flow regime is. c) Determine the pressure loss along the length of the pipe. d) Determine the power a pump would need to supply in order to overcome the friction in the pipe.
The rate of flow of water through a horizontal pipe is 200+last two digits of your id lit/s. Thearea of the pipe suddenly enlarges from 300 cm2to 1200 cm2. The pressure intensity in thesmaller pipe is 10+last digit of your id N/cm2. Determine:a) Loss of head due to sudden enlargementb) Pressure intensity in the larger pipec) Power lost due to enlargement Explain with clear writing and units and diagram Also if you use tables and equation mention it with explanation
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
1.) A process fluid (μ = 3 cP, p = 1210 kg/m³) is flowing through a 5.8-cm ID pipe with an average velocity (Uavg) of 2.5 m/sec. Calculate/estimate the following: a) What is the velocity profile from the center of the pipe (r=0 cm) to the pipe wall (r; = 2.9 cm)? b) The length of the pipe (4) is 10 feet. Calculate the pressure drop through the pipe using the Hagen-Poiseuille law. c) Calculate the Reynolds number for this system. d) Is the flow in the pipe laminar or turbulent? e) Estimate the Fanning friction factor (f) in this system. f) What is the pressure drop (AP) in the system if friction is considered?
Q2) bag house filter contains 135 cylindrical filter of 0.19m diameter and 9 m height the running time before cleaning is lhr dust load is 5 gr/ft, pe =1.1 gr/cm gas flow rate to the filter 3 x 104 m/h what is the maximum thickness of the cake
A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing process, both pastes are pumped through a pipe, with the red paste lying in the centre of the pipe, as shown in Figure Q2. The pipe has an internal radius, R₂, and the segment of red paste has a radius R₁. The flow is found to follow the Poiseuille equation, i.e. u(r) = I - 1 dp 4µ dx (R2² - r²) Where u is the viscosity of the paste and is the pressure gradient. The total flow of toothpaste through the pipe is Qtot, and the flowrate of the red paste is Qred. dx The toothpaste has a density of p = 1200 kg/m³, and a viscosity of 0.03 Pa.s. The pipe has a radius R₂ = 5 cm and a length L = 2 m. a) Find an expression for the flowrate of the red toothpaste. You answer should be in dp terms of μ, R₁, R₂, P) H, b) The flow in the pipe becomes turbulent when the Reynolds number reaches 2000 (where Re is calculated using the mean velocity across the pipe). What is the maximum pressure drop along the…